User manual ROLAND STUDIO PACKAGE PRO

[. . . ] Owner's manual In order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner's manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. Copyright © 2002 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. http://www. roland. co. jp/ Contents Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] From the folder into which you installed the demo song, select "Logic RPC Pro Demo. " 10. When the demo song opens, press the SI-24's [PLAY] button to play back the demo song. If the demo song does not play, check the following points. ·Are the SI-24 and computer (RPC-1) correctly connected via the R-BUS cable?·When you press the SI-24's [SYSTEM] button, is [L5] (1) lit and [MIDI ctrl] (6) dark?·In Logic RPC Pro, are the "Audio hardware & drivers" and "Control Surface" settings correct? 18 Quick start Let's try operating Logic RPC Pro Go ahead and use the SI-24 to control the demo song as described below. Transport [PLAY]: [STOP]: [REW]: [FF]: [PAUSE]: Jog dial: Play back Stop playback. If you press this while stopped, you're returned to the beginning of the song. To decrease the speed, press [REW] (during [FF]), or [FF] (during [REW]). CH ASSIGN Use CH ASSIGN to select the items that will be controlled. The correspondence between CH ASSIGN and the controlled items is shown below. [INPUT]: Inputs [OUTPUT]: Outputs [BUS]: Buses [Tr 1-12]: Tracks 1--12 [Tr 13-24]: Tracks 13--24 Faders 1--12 Control the faders of Logic. STATUS buttons The STATUS buttons control MUTE/SOLO/REC/PLAY/AUTOMIX for each channel. When STATUS MODE is MUTE Switches channel muting on/off. Dark: mute is off Lit red: mute on Blinking red: muted by solo 19 Quick start When STATUS MODE is SOLO Switches the channel solo on/off. Dark: solo off Lit red: solo on When STATUS MODE is REC/PLAY Switches the channel between recording and playback modes. Dark: Playing Blinking red: REC pause (Start recording when [REC] button is pressed) Lit red: Recording When STATUS MODE is AUTOMIX Switches the automation status of the channel. Dark: Off (automation off) Lit green: Read (read automation) Lit orange: now writing latch Lit red: now writing There are two modes in which automation can be written. Write: automation will be overwritten Latch: Automation will be overwritten at the time of movement of faders/buttons/knobs etc. 20 Quick start CH SELECT buttons Use these to specify the channel whose EQ/send level you want to control. The selected button will light red. PAN 1--12 Control the channel pan. EQ/SEND button When you press the EQ/SEND button so it lights in red, you can use the EQ GAIN 1--4 / EQ FREQ 1--4 / SEND 1--4 knobs to control the EQ/send levels of the channel selected by CH SELECT. On and Off of EQ for each tracks can be switched by pressing buttons for each tracks. Use the mouse to assign EQ/SEND to the channel. PLUG-IN button When you press the PLUG-IN button so it lights in red, you can control plug-in parameters for the channel selected by CH SELECT. Use the [ON 1]--[ON 2] buttons to select the insert slot that you want to control. The plug-in parameters to which the SI-24's knobs 1--10 correspond will depend on the plug-in. By switching the plug-in window from Editor mode to Control mode, you can view the approximate correspondence. In most cases, the parameters from top to bottom correspond to knobs 1--10. 21 Quick start MARKER button When you press the MARKER button so it lights in red, the [1]--[0] buttons will have the following functions. [0]: Create a marker, [1]--[9]: Move to markers 1--9 SHORTCUT button When you press the SHORTCUT button so it lights in red, the [1]--[0] buttons will execute the following commands. [1]: Save, [2]: Redo, [3]: Copy, [4]: Paste, [5]: Delete, [6]: MIDI Scrub, [7]: Cycle, [8]: Drop, [9]: Volume automation data, [0]: Pan automation data SCREEN SET button When you press the SCREEN SET button so it lights in red, the [1]--[9] buttons can be used to recall screen sets. The Screen Set function stores information about how you have the windows arranged. [. . . ] 28 Surround Bounce . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 surround panning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 E EQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EQ/SEND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]