User manual ROLAND PCR-800

[. . . ] Owner's Manual Contents Names of things and what they do . . . . . . . . . . . . . . . . 4 Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Side panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Saving a control map on your computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Loading a control map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Specify the range of the data entry MSB (CC#6). (-> Specifying the value range (upper/lower limits) (p. 65). 54 Settings (Edit mode) System exclusive assign You can assign a system exclusive message to a controller. Advanced editing 2 lets you assign a single-byte system message (system realtime message, tune request). Advanced editing 3 and 4 let you freely assign a message of up to twenty-four bytes. Edit Basic editing Controller [A1 (0)] Display Content Sys Ex. message Value range Range of initial settings Ending condition Enter F7 Remarks/Limitations First byte fixed at F0 Advanced editing 1 [A2 (1)] Sys Ex. message Can be specified Enter F7 First byte fixed at F0 Advanced editing 2 [A3 (2)] 1-byte system message -- -- [0­5, 7, 9, D, E], [DATA], and [CHECKSUM] buttons are unavailable Advanced editing 3 [A4 (3)] Any MIDI message Range of initial settings Specified number of bytes [CHECKSUM] button is unavailable Advanced editing 4 [A5 (4)] Any MIDI message Can be specified Specified number of bytes [CHECKSUM] button is unavailable System exclusive assign lets you automatically calculate the checksum, or insert variable data or a channel/block number into the message. 64) will be Hexadecimal. 55 Settings (Edit mode) System exclusive assignment procedure 1 fig. H-Edit. eps Press the [EDIT] button so it's lit. Using basic editing or advanced editing 1 fig. D-F0. eps The first byte "F0" of the system exclusive message (the beginning status) will blink. (This "F0" byte cannot be changed. ) 8 9 fig. D-Edit. eps Verify that the display is correct, and press the [ENTER] button. Use the VALUE knob or controllers [A1]­[A8] and [B1]­[B8] to enter the second byte. The display will indicate "EDIT. " 10 Check the indication in the display, then press the [ENTER] button. 2 fig. D-r1. eps Slightly move the controller to which you want to assign a system exclusive message. The display will indicate the number of the controller you selected. 11 Enter the third and subsequent bytes in the same way. 12 When you've finished entering the message, use the controllers to enter "F" and "7" as the final "F7" status (End Of Exclusive). 3 4 Check the indication in the display, then press the [ENTER] button. Turn the VALUE knob or press controller [A1 (0)] to display the basic editing "SE0" indication. * If you want to select advanced editing, press a controller [A2 (1)]­[A5 (4)] to display the "SE1"­"SE4" indication. 13 Press the [ENTER] button. If you're using advanced editing 1, specify the upper and lower value limits. 45)) fig. D-SysEx. eps 5 6 14 Specify the output port. (-> Port setting (p. 65)) fig. D-SysExEdit0. eps 15 As appropriate for the type of controller, set the button mode (p. Now you can proceed to the basic editing/advanced editing 1 procedure. For details on the actual assignments, refer to System exclusive message assignment examples (p. 58). 56 Settings (Edit mode) Using advanced editing 2 fig. D-F. eps Using advanced editing 3 or 4 fig. D-LSBSelect. eps The display will indicate "F-. " * The ­ portion shows the currently specified value. The display will indicate "L- - -. " * The - - - portion shows the currently specified value. 8 9 Use the VALUE knob or controllers [A7 (6)], [B1 (8)], [B3 (A)]­[B5 (C)], and [B8 (F)] to specify the system exclusive message. Press the [ENTER] button. 8 9 Use controllers [A1]­[A8] and [B1]­[B2] to enter the number of bytes you'll be entering, as a decimal number. Press the [ENTER] button. 10 Specify the output port. (-> Port setting (p. 65)) 10 Use controllers [A1]­[A8] and [B1]­[B8] to enter the first byte. [. . . ] TEL: 596 596 426860 Gigamusic SARL 10 Rte De La Folie 97200 Fort De France Martinique F. W. I. TEL: 596 596 715222 IRELAND Roland Ireland G2 Calmount Park, Calmount Avenue, Dublin 12 Republic of IRELAND TEL: (01) 4294444 QATAR Badie Studio & Stores P. O. 15J-150 Jakarta Pusat INDONESIA TEL: (021) 6324170 UKRAINE EURHYTHMICS Ltd. TEL: (323) 890 3700 KOREA Cosmos Corporation 1461-9, Seocho-Dong, Seocho Ku, Seoul, KOREA TEL: (02) 3486-8855 BARBADOS A&B Music Supplies LTD 12 Webster Industrial Park Wildey, St. Michael, Barbados TEL: (246)430-1100 BELGIUM/FRANCE/ HOLLAND/ LUXEMBOURG Roland Central Europe N. V. [. . . ]