User manual ROLAND M-380

[. . . ] Owner's Manual Before using this unit, carefully read the sections entitled: "IMPORTANT SAFETY INSTRUCTIONS" (p. These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner's manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. Copyright © 2009 ROLAND CORPORATION All rights reserved. [. . . ] The MUTE GROUP ASSIGN popup will appear. Mute groups fig. ScrMUTEGroupAssignGuide. eps A B You can also make the setting for switching MUTE groups on or off from a USER button (p. In the MUTE GROUP screen, the function buttons perform the following operations. [F1 (MUTE1)] [F2 (MUTE2)] [F3 (MUTE3)] [F4 (MUTE4)] [F6 (MUTE ALL OUT)] [F7 (NAME EDIT)] [F8 (ASSIGN)] Turns MUTE group 1 on/off. 117 A. Target mute group indication This indicates the mute group to which the settings in the MUTE GROUP ASSIGN popup will apply. B. Channel select buttons Here you can select the channels that will be assigned to the mute group. In the MUTE GROUP ASSIGN screen, the function buttons perform the following operations. Output muting controlled by [F6 (MUTE ALL OUT)] cannot be stored in a scene memory. When the M-380 is started up, muting caused by [F6 (MUTE ALL OUT)] will be turned off. 117 Mute groups [F1 (CH 1­24)] [F2 (CH 25­48)] [F3 (AUX/MAIN/MARIX)] [F8 (CLOSE)] 3. Displays CH1­CH24 as the channel select buttons. Displays AUX1­AUX16, MATRIX1­MATRIX8, MAIN L/R and MAIN C as the channel select buttons. Closes the popup. Specifying a name and color label for a mute group You can specify a name and color label for each mute group. A name of up to six characters can be specified, and you can choose one of eight colors as the color label. The NAME EDIT popup is used to edit the name and select a color label. Move the cursor to the desired channel select button, and press [ENTER] to select it. For details on name editing, refer to "Specifying a channel name and color label" (p. 51). 4. When the MUTE GROUP ASSIGN popup is displayed, you can press a top panel [SEL] to turn on/off the corresponding channel's assignment to the mute group. Accessing the NAME EDIT popup 1. Access the MUTE GROUP screen. fig. ScrMUTEGroup. eps Using mute groups 1. Access the MUTE GROUP screen. fig. ScrMUTEGroup. eps Mute groups 2. Move the cursor to the MUTE group button of the desired mute group, and press [F7 (NAME EDIT)]. fig. ScrChNameEdit. eps 2. Move the cursor to the desired mute group button, and press [ENTER] to turn it on/off. You can also make the setting for switching MUTE groups on or off from a USER button (p. 154). The NAME EDIT popup will appear. 118 Talkback/Oscillator About talkback and oscillator fig. TB-OSCFlow. eps MAIN AUX SOLO LR 1 2 16 L R OSCILLATOR PINK NOISE WHITE NOISE SINE WAVE OSC LEVEL OSC LEVEL OSC ON MAIN L, R, AUX 1-16, MATRIX 1-8 SW SW TO MAIRIX 1-8 TO OUTPUT PATCHBAY TALKBACK PHANTOM +48V GAIN TALKBACK LEVEL TALKBACK LEVEL A/D TALKBACK ON MAIN L, R, AUX 1-16, MATRIX 1-8 SW SW TO MAIRIX 1-8 TO OUTPUT PATCHBAY TALKBACK MIC LR 1 2 16 L R MAIN AUX SOLO Talkback is a function that sends the input of a mic connected to the TALKBACK MIC IN on the rear panel jack to an AUX bus, MATRIX bus, MAIN L/R bus or MAIN C bus. This is useful when the mixer operator needs to convey instructions to performers on stage or to staff. Oscillator is a function that generates pink noise, white noise, or a sine wave, and sends it to an AUX bus, MATRIX bus, MAIN L/R. This is useful when you need to measure the acoustical response of a hall, or when checking the connections of external devices. You can also output the talkback or the oscillator directly via the output patchbay without routing the signal through a bus. Talkback/Oscillator section Talkback and oscillator operations are performed in the Talkback/Oscillator section. fig. TalkbackOscSectGuide. eps A Talkback/Oscillator B C A. MIC LEVEL knob This adjusts the preamp gain of the TALKBACK MIC input. DISP button This accesses the TALKBACK/OSCILLATOR screen, where you can make talkback settings and oscillator settings. It will be lit when talkback is on. B. C. 119 Talkback/Oscillator Using talkback Talkback settings are made in the TALKBACK tab of the TALKBACK/OSCILLATOR screen. [. . . ] 153 USER LEVEL popup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152, 154­155 USER screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 W Wait message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 241 For China For the USA Model Name : Type of Equipment : Responsible Party : Address : Telephone : M-380 Digital Mixer Roland Systems Group U. S. [. . . ]