User manual ROLAND KR-375 V1.00 MIDI IMPLEMENTATION

[. . . ] MIDI IMPLEMENTATION Model: KR375 Date: Mar. 1. 1998 Version: 1. 00 Section 1. Receive data Channel Voice Messages Note off Status 8nH 9nH 2nd byte kkH kkH 3rd byte vvH 00H Portamento Time (Controller number 5) Status BnH 2nd bytes 05H 3rd byte vvH n = MIDI channel number : 0H-FH (ch. 1-ch. 16) vv = Portamento Time : 00H-7FH (0-127), Initial value = 00H (0) * This adjusts the rate of pitch change when Portamento is ON or when using the Portamento Control. A value of 0 results in the fastest change. n = MIDI channel number : 0H-FH (ch. 1-ch. 16) kk = note number : 00H-7FH (0-127) vv = note off velocity : 00H-7FH (0-127) * * For Drum Parts, these messages are received when Rx. NOTE OFF = ON for each Instrument. The velocity values of Note Off messages are ignored. Data Entry (Controller number 6, 38) Status BnH BnH 2nd bytes 06H 26H 3rd byte mmH llH n = MIDI channel number : 0H-FH (ch. 1-ch. 16) mm, ll = the value of the parameter specified by RPN/NRPN Note on Status 9nH 2nd bytes kkH 3rd byte vvH Volume (Controller number 7) Status BnH 2nd bytes 07H 3rd byte vvH n = MIDI channel number : 0H-FH (ch. 1-ch. 16) kk = note number : 00H-7FH (0-127) vv = note on velocity : 01H-7FH (1-127) * * Not received when Rx. NOTE MESSAGE = OFF. [. . . ] 40 03 1A 40 03 1B 00 00 01 00 00 01 00 - 7F 00 - 7F EFX Send Level to Reverb EFX Send Level to Chorus EFX Depth EFX Control Source 1 Dry 100% - EFX 100% 00: OFF 01 - 5F: Control Change No. 71: CAf 72: Bender *Refer to EFX Control Source 1 7F 00 40 03 1C 00 00 01 00 - 7F EFX Control Depth 1 40 03 1D 00 00 01 00 - 7F EFX Control Source 2 40 03 1E 00 00 01 00 - 7F EFX Control Depth 2 * Marked #1 or #2 can be controlled by EFX CONTROL SOURCE 1 or 2. 7F 00 7F -100% - +100% -100% - +100% Part Parameters KR375 has 16 parts. Parameters that can be set individually for each Part are called Part parameters. If you use exclusive messages to set Part parameters, specify the address by Block number rather than Part Number (normally the same number as the MIDI channel). The Block number can be specified as one of 16 blocks, from 0 (H) to F (H). x. . . BLOCK NUMBER (0-F), Part 1 (MIDI ch = 1) x = 1 Part 2 (MIDI ch = 2) x = 2 : :: Part 9 (MIDI ch = 9) x = 9 Part10 (MIDI ch = 10) x = 0 Part11 (MIDI ch = 11) x = A Part12 (MIDI ch = 12) x = B : :: Part16 (MIDI ch = 16) x = F Default Value (H) Description 00 0 00 1 Same as the Part Number 01 ON 01 ON 01 ON 01 ON 01 ON 01 ON 01 ON 00 (01*) OFF (ON*) Address (H) Size (H) Data (H) Parameter Description 40 1x 00 00 00 02 00-7F TONE NUMBER CC#00 VALUE 0-127 40 1x 01# 00-7F P. C. NRPN is set to OFF by power-on or by receiving "Turn General MIDI System On, " and it will be set ON when "GS RESET" is received. 40 1x 0B 40 1x 0C 40 1x 0D 40 1x 0E 40 1x 0F 40 1x 10 40 1x 11 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00-01 00-01 00-01 00-01 00-01 00-01 00-01 Rx. SOSTENUTO OFF/ON OFF/ON OFF/ON OFF/ON OFF/ON OFF/ON OFF/ON 01 01 01 01 01 01 01 ON ON ON ON ON ON ON 8 40 1x 12 40 1x 13 40 1x 14 0 * 00 00 01 00 00 01 00 00 01 00-01 00-01 00-02 Rx. SOFT MONO/POLY MODE (= CC# 126 01 / CC# 127 00) ASSIGN MODE OFF/ON Mono/Poly 0 = SINGLE 1 = LIMITED-MULTI 01 01 00 at x = 0 01 at x 0 ON Poly SINGLE at x = 0 LIMITED-MULTI at x 2 = FULL-MULTI ASSIGN MODE is the parameter that determines how voice assignment will be handled when sounds overlap on identical note numbers in the same channel (i. e. , repeatedly struck notes). This is initialized to a mode suitable for each Part, so for general purposes there is no need to change this. 0 = OFF 00 at x 0 OFF at x 0 1 = MAP1 01 at x = 0 MAP1 at x 0 2 = MAP2 This parameter sets the Drum Map of the Part used as the Drum Part. KR375 can simultaneously (in different Parts) use up to two Drum Maps (MAP1, MAP2). With the initial settings, Part10 (MIDI CH = 10, x = 0) is set to MAP1 (1), and other Parts are set to normal instrumental Parts (OFF (0)). 00 00 01 00-02 USE FOR RHYTHM PART 40 1x 15 * 40 1x 16 00 00 01 28-58 PITCH KEY SHIFT -24 - +24 [semitones] 40 0 [semitones] 40 1x 17 00 00 02 08-F8 PITCH OFFSET FINE -12. 0 - +12. 0 [Hz] 08 00 0 [Hz] 40 1x 18# Use nibblized data. * PITCH OFFSET FINE allows you to alter, by a specified frequency amount, the pitch at which notes will sound. This parameter differs from the conventional Fine Tuning (RPN #1) parameter in that the amount of frequency alteration (in Hertz) will be identical no matter which note is played. When a multiple number of Parts, each of which has been given a different setting for PITCH OFFSET FINE, are sounded by means of an identical note number, you can obtain a Celeste effect. 40 1x 19 40 1x 1A 40 1x 1B 40 1x 1C 40 1x 1D 40 1x 1E 40 1x 1F 40 1x 20 40 1x 21 40 1x 22 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-5F 00-5F 00-7F 00-7F PART LEVEL (= CC# 7) VELOCITY SENSE DEPTH VELOCITY SENSE OFFSET PART PANPOT (= CC# 10, except RANDOM) KEY RANGE LOW KEY RANGE HIGH CC1 CONTROLLER NUMBER CC2 CONTROLLER NUMBER CHORUS SEND LEVEL (= CC# 93) REVERB SEND LEVEL (= CC# 91) 0-127 0-127 0-127 -64 (RANDOM), -63 (LEFT) - +63 (RIGHT) (C-1)-(G9) (C-1)-(G9) 0-95 0-95 0-127 0-127 64 40 40 40 00 7F 10 11 00 28 100 64 64 0 (CENTER) C-1 G9 16 17 0 40 40 1x 23 00 00 01 00-01 Rx. BANK SELECT is set to ON by power-on or by receiving "GS RESET, " and will be set OFF when "Turn General MIDI System On" is received. 40 1x 24 00 00 01 00-01 Rx. BANK SELECT LSB * KR375 can be recognise Bank Select LSB (40H-43H) even if this message is OFF. 40 1x 25 40 1x 28 40 1x 29# 40 1x 30 40 1x 31 40 1x 32 40 1x 33 40 1x 34 40 1x 35 40 1x 36 40 1x 37 00 00 01 00 00 03 00-01 00-7F TONE REMAIN Bank Select LSB Range OFF/ON 00 ON (OFF*) OFF OFF/ON LSB (from) LSB (to) -50 - +50 -50 - +50 -50 - +50 -50 - +50 -50 - +50 -50 - +50 -50 - +50 -50 - +50 01 40 43 40 40 40 40 40 40 40 40 ON 40H 43H 0 0 0 0 0 0 0 0 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 0E-72 0E-72 0E-72 0E-72 0E-72 0E-72 0E-72 0E-72 TONE MODIFY 1 Vibrato rate (= NRPN# 8) TONE MODIFY 2 Vibrato depth (= NRPN# 9) TONE MODIFY 3 TVF cutoff frequency (= NRPN# 32) TONE MODIFY 4 TVF resonance (= NRPN# 33) TONE MODIFY 5 TVF&TVA Env. attack (= NRPN# 99) TONE MODIFY 6 TVF&TVA Env. decay (= NRPN# 100) TONE MODIFY 7 TVF&TVA Env. release (= NRPN# 102) TONE MODIFY 8 Vibrato delay (= NRPN# 10) 40 1x 40 00 00 0C 00-7F SCALE TUNING C -64 - +63 [cent] 40 0 [cent] 40 1x 41# 00-7F SCALE TUNING C# -64 - +63 [cent] 40 0 [cent] 40 1x 42# 00-7F SCALE TUNING D -64 - +63 [cent] 40 0 [cent] 40 1x 43# 00-7F SCALE TUNING D# -64 - +63 [cent] 40 0 [cent] 40 1x 44# 00-7F SCALE TUNING E -64 - +63 [cent] 40 0 [cent] 40 1x 45# 00-7F SCALE TUNING F -64 - +63 [cent] 40 0 [cent] 40 1x 46# 00-7F SCALE TUNING F# -64 - +63 [cent] 40 0 [cent] 40 1x 47# 00-7F SCALE TUNING G -64 - +63 [cent] 40 0 [cent] 40 1x 48# 00-7F SCALE TUNING G# -64 - +63 [cent] 40 0 [cent] 40 1x 49# 00-7F SCALE TUNING A -64 - +63 [cent] 40 0 [cent] 40 1x 4A# 00-7F SCALE TUNING A# -64 - +63 [cent] 40 0 [cent] 40 1x 4B# 00-7F SCALE TUNING B -64 - +63 [cent] 40 0 [cent] * SCALE TUNING is a function that allows fine adjustment to the pitch of each note in the octave. [. . . ] B2 (B2) (B2) (B2) (B2) (B2) 64 00 65 01 06 45 26 03 64 7F 65 7F MIDI ch. 3, lower byte of RPN parameter number: 00H (MIDI ch. 3) upper byte of RPN parameter number: 01H (MIDI ch. 3) upper byte of parameter value: 45H (MIDI ch. 3) lower byte of parameter value: 03H (MIDI ch. 3) lower byte of RPN parameter number: 7FH (MIDI ch. 3) upper byte of RPN parameter number: 7FH The values in the table are given in cents. Refer to the explanation of Scale Tuning on page 9 to convert these values to hexadecimal, and transmit them as exclusive data. For example, to set the tune (C-B) of the Part1 Arabian Scale, send the data as follows: F0 41 10 42 12 40 11 40 3A 6D 3E 34 0D 38 6B 3C 6F 40 36 0F 50 F7 Copyright(c) 1998 ROLAND CORPORATION All right reserved. No part of this publication may reproduced in any form without the written permission of ROLAND CORPORATION. 13 EFX Type Table MSB 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 01H 02H 02H 02H 02H 02H 02H 02H 02H 02H 02H 02H 02H 11H 11H 11H LSB 00H 01H 02H 10H 11H 20H 21H 22H 23H 24H 30H 31H 40H 41H 42H 43H 50H 51H 52H 53H 54H 55H 56H 60H 61H 00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 00H 01H 02H Type Equalizer Spectrum Enhancer Overdrive Distortion Phaser Auto Wah Rotary Stereo Flanger Step Flanger Compressor Limiter Hexa Chorus Tremolo Chorus Stereo Chorus Space D Stereo Delay Modulation Delay Triple Tap Delay QuadrupleTap Delay Time Controlable Delay Reverb Gate Reverb Feedback Pitch Shifter 2 Voice Pitch Shifter Overdrive -> Chorus Overdrive -> Flanger Overdrive -> Delay Distortion -> Chorus Distortion -> Flanger Distortion -> Delay Enhancer -> Chorus Enhancer -> Flanger Enhancer -> Delay Chorus -> Delay Flanger -> Delay Chorus -> Flanger Chorus / Delay Flanger / Delay Chorus / Flanger 01H, 02H: Enhancer No 1 2 17 18 20 Parameter Sence. [. . . ]