User manual ROLAND JUPITER-80

[. . . ] WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS. IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING - When using electric products, basic precautions should always be followed, including the following: 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] 29). Other Convenient Functions 2. Move the cursor to Write Destination, and use the value dial or the [DEC] [INC] buttons to select the write destination . Registration number Connecting Other Equipment Appendix MEMO You can also use the bank buttons ([A]­[D]) and Registration buttons ([1]­[8]) to directly specify the write destination. 53 Editing a Registration If the following display appears when you save If Live Set parameters or SuperNATURAL Synth Tone parameters have been edited, the corresponding Live Set or SuperNATURAL Synth Tone will be highlighted when you save the Registration. 2. If you want to specify the Live Set number or SuperNATURAL Synth Tone number for saving, touch <SELECT DEST> . Live Set Select Destination screen will appear. The Synth Tone has been edited. The Live Set has been edited. 3. Select the write destination . 1 Select the write destination for the Live Set. 2 You have the option of saving the edited Live Sets and SuperNATURAL Synth Tones at the same time that you save the Registration. If you want to do this, proceed as follows. Select the write destination for the SuperNATURAL Synth Tone. 1. Select the Write check box for the Live Sets and SuperNATURAL Synth Tones that you want to save . 3 Confirm selections and return to the previous screen. 4. Touch <WRITE> . MEMO · If you specify the same write destination for the Live Sets of the Upper Part and Lower Part, the message "Cannot Write!" will appear. · If you specify the same write destination for the SuperNATURAL Synth Tones of layers 1­4, the message "Cannot Write!" will appear. · If the same Live Set is assigned to the Upper Part and the Lower Part, and you edit only one Part and then execute this operation, the edited Live Set will be assigned to the other Part as well. · If the same SuperNATURAL Synth Tone is assigned to layers 1­4, and you edit only the SuperNATURAL Synth Tone of a specific layer and then execute this operation, the edited SuperNATURAL Synth Tone will also be assigned to the other layers. MEMO If you save without selecting these check boxes, only the Registration will be saved. The Live Sets or SuperNATURAL Synth Tones you've edited will remain in their edited state without being saved. If you want to specify a Live Set number or SuperNATURAL Synth Tone number at which to save the data, proceed to step 2. If you want to save the data by overwriting the current Live Set number and SuperNATURAL Synth Tone number, proceed to step 4. 54 Editing a Registration Initializing a Registration Here's how to initialize the currently selected Registration. MEMO · Initializing the Registration will affect the data in the temporary area (p. When you initialize the Registration, the Live Sets and tones in the temporary area will also be initialized. · If you want to return the parameters of all sounds to their factory-set state, use Factory Reset (p. 31), touch <UTILITY> . Playing Sounds Registration Utility Menu screen will appear. Editing Sounds 2. Touch <Registration Initialize>, and then touch <Select> . Other Convenient Functions A message will ask "Are you sure?" 3. Connecting Other Equipment Touch <OK> . Appendix 55 Editing a Live Set You can edit a Live Set by switching the Tones in the Live Set, and by adjusting offset values relative to the value of each tone. 32) shows basic information about the currently selected Live Set. View the Live Set Effects Routing screen. Tips for editing a Live Set Choose which Parts will be heard A Registration consists of up to four Parts. Editing will be easier if you're listening only to the Parts that are selected for the Live Set you want to edit (p. 37). Level of each layer. View the Live Set Common screen. View the Live Set Effects screen. MEMO When you edit the parameters of a Live Set, you are specifying a relative increase or decrease applied to the value of the Tone; the actual tone itself is not affected. This means that even if the same tone is used by another Live Set, you'll be able to edit without affecting the other Live Set. Basic Editing Operations for Live Sets To edit a Live Set, you'll start from the Live Set screen. View the Live Registration screen. Tone name Switch between the Upper Part and Lower Part 1. In the Live Set screen (p . 32), touch the button (<COMMON>, <LAYER>, <EFFECTS>) of the parameter that you want to edit . The following parameters are stored in a Live Set. Tab Explanation Settings common to the entire Live Set · Live set name, Live Set category COMMON · Volume · Filter · Phase lock, etc. Settings for each layer · Layer on/off LAYER · Volume · Pan · Layer audio output destination and send level · Keyboard range, etc. MFX settings · Layer audio output destination and send level · Send level to MFX · MFX on/off EFFECTS · MFX type selection · MFX volume · MFX settings, reverb settings · Send levels from the Tone to reverb, and from MFX to reverb, etc. Offset settings for each layer For a SuperNATURAL Synth Tone · Pitch MODIFY · Filter · Amp · LFO · Modulation · Portamento, etc. [. . . ] Box 922846 Amman 11192, JORDAN TEL: (06) 5692696 COSTA RICA JUAN Bansbach Instrumentos Musicales Ave. 1. Calle 11, Apartado 10237, San Jose, COSTA RICA TEL: 258-0211 KOREA Cosmos Corporation 1461-9, Seocho-Dong, Seocho Ku, Seoul, KOREA TEL: (02) 3486-8855 POLAND ROLAND POLSKA SP. Kty Grodziskie 16B 03-289 Warszawa, POLAND TEL: (022) 678 9512 URUGUAY Todo Musica S. A. Francisco Acuna de Figueroa 1771 C. P. : 11. 800 Montevideo, URUGUAY TEL: (02) 924-2335 KUWAIT EASA HUSAIN AL-YOUSIFI & SONS CO. [. . . ]