User manual ROLAND GT-10B

[. . . ] Owner's Manual Thank you, and congratulations on your choice of the BOSS GT-10B. 201b Before using this unit, carefully read the sections entitled: "USING THE UNIT SAFELY" (p. These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner's manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. PHRASE LOOP ON / OFF BPM 202 Copyright © 2008 BOSS CORPORATION All rights reserved. [. . . ] 63) is set to "Bass 1­3. " 96 Chapter 7 Using the GT-10B Connected to a Computer Via USB Setting the Direct Monitor Switches the output of the GT-10B sound to the OUTPUT and PHONES jacks. SYSTEM 1. The SYSTEM MENU screen appears. Select USB. 2. The USB screen appears. 3. 4. Move the cursor to Dir. Monitor. 5. Select the Monitor mode. For more information on signal paths set by the Direct Monitor parameter settings, refer to "Signal Flow" (p. 142). Parameter/ Range Off Explanation Audio signal Audio IN Audio OUT Computer Set this to Off if transmitting audio data internally through a computer (Thru). No sound is heard at this time unless the setting for the computer is Thru. Set this to On when using the GT-10B as a standalone device, without connecting to a computer. (When the Dir. Monitor parameter is set to Off, only sounds from USB In are audible. ) USB OUT USB IN On Dir. Monitor Bass Amp OUTPUT L/R GT-10B sound PHONES Headphones Chapter 7 · · This setting cannot be saved. If you are using the special driver, you can control Dir. Monitor On/Off from ASIO 2. 0-compatible application. 97 Chapter 7 Using the GT-10B Connected to a Computer Via USB Controlling the Direct Monitor Setting from a Computer This setting determines whether or not the command (the Direct Monitor command) controlling the Direct Monitor setting (p. Select USB. 2. The USB screen appears. 3. 4. Move the cursor to Monitor Cmd. 5. Set the desired value. Parameter/ Range Disable Enable Explanation The Direct Monitor command is disabled, maintaining the Direct Monitor mode set by the GT-10B. The Direct Monitor command is enabled, allowing the Direct Monitor mode to be switched from a computer. Recording the GT-10B's Output with a Computer In the computer application, set the audio input port to the GT-10B. If passing audio data through the software you're using, switch the direct monitor off. 98 Chapter 7 Using the GT-10B Connected to a Computer Via USB Applying GT-10B Effects to a Computer's Audio Playback In the computer application, set the audio output port to the GT-10B. You can use the GT-10B to apply effects to the audio data played by the computer, then record the data again with the computer. Use this process when, for example, you want to add effects to existing audio data. 1. SYSTEM The SYSTEM MENU screen appears. Select the INPUT SELECT (page 1) screen. 4. 5. Set the INPUT SELECT parameter to USB In. · · Set the software so audio is not passed through it. Set the Dir. Monitor parameter to On. Parameter/ Range Bass 1­3 USB In Explanation Effects are applied to the signals input via the INPUT jacks. Effects are applied to the signals input via USB. Chapter 7 99 Chapter 8 Parameters Guide In this chapter you will find detailed descriptions for each of the GT-10B's effects and the parameters used to control them. · · · · The format used for parameter names is based on how the names are displayed when the screen is in list view. The sound that is input to each effect is called the "direct sound, " and the sound modified by the effect is called the "effect sound. " MONO This effect sound is mono. This effect sound is output with two channels. STEREO The trademarks listed in this document are trademarks of their respective owners, which are separate companies from Roland/BOSS. Those companies are not affiliated with Roland/BOSS and have not licensed or authorized BOSS's GT-10B. Their marks are used solely to identify the equipment whose sound is simulated. Parameter/ Range Sustain *1 0­100 Adjusts the range (time) over which low-level signals are boosted. Adjusts the strength of the picking attack when the strings are played. Higher values result in s sharper attack, creating a more clearly defined sound. When the input signal level exceeds this threshold level, limiting will be applied. [. . . ] 35 List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Volume-swell Effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 W WAH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]