User manual ROLAND E-56 MIDI IMPLEMENTATION

[. . . ] Reissued in 1994, the DELUXE REVERB® is truly one of Fender's finest amps and a perennial best-seller to this day. fig. DeluxeReverb. eps 3 Panel Descriptions fig. E-56_name1. eps 1. AC Adaptor Jack 12 This jack accepts the connection of an AC adaptor (optionally available BOSS PSA-series). By using an AC adaptor, you can play without being concerned about how much battery power you have left. * Use only the specified AC adaptor (PSAseries), and make sure the line voltage at the installation matches the input voltage specified on the AC adaptor's body. [. . . ] BASS Knob This knob controls the tone of the effect at lower frequencies. 11. GAIN Knob This adjusts the amount of distortion and the volume level. Turning it clockwise makes distortion stronger and increases the volume level. VIBRATO Knob This adjusts the amount of vibrato effect (cyclical fluctuations in volume) that is applied. Turning the VIBRATO knob while depressing the pedal switch changes the vibrato rate (RATE setting mode). * No sound is output when this knob is turned completely counterclockwise. 6 Connections * Inserting a connecting plug into the INPUT jack turns on the power to the unit. * Raise the amp volume only after turning on the power to all connected devices. * The use of an AC adaptor is recommended as the unit's power consumption is relatively high. * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. * If there is a battery in the unit while an AC adaptor is being used, normal operation will continue should the line voltage be interrupted due to power blackout or power cord disconnection. When connection cables with resistors are used, the sound level may be extremely low, or impossible to hear. The rate is stored. OffRate confirmed * Vibrato rate for use with the tempo settings can be made in the range of 0. 3­3. 0 seconds. * If you carry out Step 3 immediately after Step 2, Step 3 may inadvertently be interpreted as tempo input, thus changing the RATE setting. Allow a brief interval to pass before progressing from Step 2 to Step 3. * You can also set the rate by turning the VIBRATO knob while depressing the pedal switch (p. When you've finished setting the rate, release the pedal switch, then depress it again, holding it down for two or more seconds. 13 Changing the Battery When the indicator goes dim or no longer lights while the effect is on, it means that the battery must be replaced. Replace the battery following the steps below. * The use of an AC adaptor is recommended as the unit's power consumption is relatively high. Should you prefer to use a battery, please use the alkaline type. fig. replace-battery. eps 1. Hold down the pedal and loosen the thumbscrew, then open the pedal upward. * The pedal can be opened without detaching the thumbscrew completely. Thumbscrew Pedal Spring Base 2. Remove the old battery from the battery housing, and remove the snap cord connected to it. Connect the snap cord to the new battery, and place the battery inside the battery housing. * Be sure to carefully observe the battery's polarity (+ versus -). Battery Snap Cord Coil Spring Guide Bush Hole 4. Slip the coil spring onto the spring base on the back of the pedal, and then close the pedal. * Carefully avoid getting the snap cord caught in the pedal, coil spring, and battery housing. Battery Snap Battery Housing 9V Battery 5. [. . . ] 8). * The power is switched on only when a cable is Could you be in the vibrato rate setting mode (p. 13)? 15 Setting Samples Standard Crunch Sound fig. E-56-sample1. eps Surf Rock Sound fig. E-56-sample1. eps Hard Overdrive Sound fig. E-56-sample1. eps Vibrato Sound fig. E-56-sample1. eps For details about the vibrato rate, please refer to p. * All product names mentioned in this document are trademarks or registered trademarks of their respective owners. In this document, their names are used solely to identify the equipment whose sound is simulated by COSM. 20 MEMO 21 MEMO 22 For EU Countries This product complies with the requirements of European Directive 89/336/EEC. For the USA FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ]