User manual ROLAND CY-12C

[. . . ] Owner's Manual Thank you, and congratulations on your choice of the Roland CY-12R/C V-Cymbal. Before using this unit, carefully read the sections entitled: "USING THE UNIT SAFELY" (p. These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner's manual should be read in its entirety. [. . . ] For information on cable specifications, contact the manufacturer of the cable. · For everyday cleaning wipe the unit with a soft, dry cloth or one that has been slightly dampened with water. To remove stubborn dirt, use a cloth impregnated with a mild, non-abrasive detergent. Afterwards, be sure to wipe the unit thoroughly with a soft, dry cloth. 402 · Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or deformation. 4 Attaching to a Stand Attach the CY-12R/C with the optional cymbal mount (MDY series), or drum stand cymbal mount (MDS series). Output Jack BOW/BELL 1. Use a commercially available drum key to tighten the stopper bolt. The stopper keeps the CY-12R/C from turning, and prevents the cables from catching or getting tangled on the stand. fig. 01. e BOW/EDGE Corresponding Play Methods Bow Shot (p. Contact between the cable and the cymbal or stand can result in problems, 5 Next such as double sounding. 3. 2. The TDW-1 with V-Cymbal Control Owner's Manual contains an explanation of how the CY-15R is used with Three Way Triggering. Substitute "CY-12R/C" for "CY-15R" as you read through the text. Should you neglect to make the appropriate settings for the percussion sound module. · Sometimes it does not sound (uneven volume) · The volume is too low (reduced sensitivity) · Double sounding may occur For information on how to change the parameters for a percussion sound module, refer to its owner's manual. Playing Methods Bow Shot This is the most common playing method, playing the pad face of the cymbal. It corresponds to the sound of the "head-side" of the connected trigger input. If Using TD-10 + TDW-1 with V-Cymbal Control When you use the TD-10 + TDW-1 V-Cymbal Control, three way triggering is possible. * Three Way Triggering is not available with the TD-8. Bow Edge Shot This playing method involves striking the edge with the shoulder of the stick. It corresponds to the sound of the "rimside" of the connected trigger input. About Three Way Triggering By using two cables to connect the CY-12R/C and a TD-10, you can then perform using three different tones: bow, bell, and edge. TDW-1 specifications allow the Three Way Triggering function to be used with only one V-Cymbal. For example, if you use the Three Way Triggering function with one CY-15R, you would not be able to use Three Way Triggering if you added another CY-12R/C. To make use of edge shot, you'll need to connect to a trigger input jack on the percussion sound module that accommodates rim shots. Edge sensor Connections/Examples of Settings CY-12R/C Output BOW/BELL BOW/EDGE TD-10 Trigger Input 10/RIDE 11/AUX1 TD-10 Trigger Type RdA CTR Bell Shot This playing method involves striking the bell. It corresponds to the sound of the "rim-side" of the connected trigger input. If you connect a pad or a V-Cymbal ONLY to the trigger input for which trigger type is set to the "CTR"(11/AUX 1), it will not work. Correspondences Between Playing Methods and Trigger Input Playing Methods Bow Shot Bell Shot Edge Shot TD-10 Trigger Input 10/RIDE Head 10/RIDE Rim 11/AUX 1 Rim · To make use of bell shot, you'll need to connect to a trigger input jack on the percussion sound module that accommodates rim shots. Bell * Head-side tones for the trigger input 11/AUX 1 cannot be sounded. For more details on the settings for Three Way Triggering, refer to the TDW-1 with V-Cymbal Control Owner's Manual. 6 Next Choking Choking (pinching) the cymbal's edge with the hand immediately after hitting the cymbal makes the sound stop. Double sounding · Are any cables touching the CY-12R/C?Secure the cables in place with the cable ties so that they do not touch the units. Also, be careful to make sure that the cables are not pulled by the movement of a cymbal when struck (p. · Are the stopper, felt washer, and wing nut attached correctly?* If double triggering still occurs, try adjusting trigger parameters, such as Retrigger Cancel, on the sound module you are using (TD-6, TD-8, TD-10, etc. ) To make use of choking play techniques, you'll need to connect to a trigger input jack on the percussion sound module that accommodates rim shots. fig. CY07. e Edge sensor The volume level is too low · If the cymbal is struck while power to the drum module (such as the TD-6, TD-8, or TD-10) is turned on, the response to light hits will be poor. Do not strike pads or cymbals while turning on the power. Troubleshooting Issues Affecting The Overall System Check these first · Is the trigger type set correctly?Make the trigger parameter settings for your percussion sound module (p. When a monaural cable is used, the sound does not change when an edge shot or a bell shot is made. [. . . ] NSW 2099 AUSTRALIA TEL: (02) 9982 8266 RUSSIA MuTek 3-Bogatyrskaya Str. 1. k. l 107 564 Moscow, RUSSIA TEL: 095 169 5043 SAUDI ARABIA aDawliah Universal Electronics APL Corniche Road, Aldossary Bldg. , 1st Floor SAUDI ARABIA P. O. Box 2154, Alkhobar 31952 SAUDI ARABIA TEL: (03) 898 2081 EUROPE AUSTRIA Roland Austria GES. M. B. H. Siemensstrasse 4, P. O. Box 74, A-6063 RUM, AUSTRIA TEL: (0512) 26 44 260 ASIA CHINA Beijing Xinghai Musical Instruments Co. , Ltd. 6 Huangmuchang Chao Yang District, Beijing, CHINA TEL: (010) 6774 7491 SPAIN Roland Electronics de España, S. A. Calle Bolivia 239, 08020 Barcelona, SPAIN TEL: (93) 308 1000 NEW ZEALAND Roland Corporation Ltd. 32 Shaddock Street, Mount Eden, Auckland, NEW ZEALAND TEL: (09) 3098 715 BELGIUM/HOLLAND/ LUXEMBOURG Roland Benelux N. [. . . ]