User manual ROLAND CDI-BR-1

[. . . ] The symbol alerts the user to items that must never be carried out (are forbidden). The specific thing that must not be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the unit must never be disassembled. [. . . ] 118 · Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes. Excessive heat can deform or discolor the unit. 355 · Should you remove screws, make sure to put them in a safe place out of children's reach, so there is no chance of them being swallowed accidentally. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . · To avoid possible breakdown, do not use the unit in a wet area, such as an area exposed to rain or other moisture. 962a * In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice. 3 Installation of the CDI-BR-1 022d · Before installing the CDI-BR-1, you must first always turn off the BR-1180 and unplug the AC adaptor. CAUTION 928 · When turning the unit upside-down, get a bunch of newspapers or magazines, and place them under the four corners or at both ends to prevent damage to the buttons and controls. Also, you should try to orient the unit so no buttons or controls get damaged. 929 · When turning the unit upside-down, handle with care to avoid dropping it, or allowing it to fall or tip over. · Use a Phillips screwdriver that is suitable for the size of the screw (a number 2 screwdriver). If an unsuitable screwdriver is used, the head of the screw may be stripped. · Be careful not to cut your hand on the edge of the installation bay. 901 · To avoid the risk of damage to internal components that can be caused by static electricity, please carefully observe the following whenever you handle the CDI-BR-1. 901-1 · Before you touch the CDI-BR-1, always first grasp a metal object (such as a water pipe), so you are sure that any static electricity you might have been carrying has been discharged. · Before you connect any cables, make sure they do not carry a static electricity charge. Such charges can be transmitted, for example, if the other end of the cable has been in contact with a carpet (or other object) where there is a static electricity buildup. If it doesn't fit properly on the first attempt, remove the board and try again. 901-4 912 913 · When CDI-BR-1 installation is complete, double-check your work. 4 Installation of the CDI-BR-1 1. Turn off the power to the BR-1180 and any connected devices, and disconnect the AC adapter and all other connector cables. Turn the BR-1180 over, remove the screws at the positions shown in the figure, and remove the cover. fig. 01 5. Replace the cover with the positions of the (A) and (B) sections of the cover are reversed relative to their positions prior to the cover's removal. fig. 04 (A) (B) (B) (A) 3. Align the CDI-BR-1's connector with the BR-1180's socket and insert the connector securely. fig. 02 6. Tighten the screws included with the CDIBR-1 in the positions indicated in the figure (C) until snug, tighten the cover attachment screws until they are snug, and then securely tighten all of the screws. fig. 05 (C) (C) (C) 7. [. . . ] Alignez le connecteur du CDI-BR-1 et la prise du BR-1180, puis insérez solidement le connecteur. fig. Placez le CD-ROM inclus dans le CDI-BR-1, puis appuyez sur [LOOP PHRASE IMPORT]. Appuyez ensuite sur CURSOR [ ] pour sélectionner « IMPORT », puis appuyez sur [ENTER]. [. . . ]