User manual ROLAND AR-200R

[. . . ] Owner's Manual Before using this unit, carefully read the sections entitled: "USING THE UNIT SAFELY" and "IMPORTANT NOTES" (p. These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner's manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. Copyright © 2006 ROLAND CORPORATION All rights reserved. [. . . ] Playback of the phrase is stopped. * If you are using a card created with the AR-3000/3000R/2000, or if you are editing a card's Control Input Playback mode with ARE-3000, set the control input playback mode to Direct Playback (normal playback). Procedure for Setting the Control Input Mode 1. Set the MODE switches on the AR-200R's bottom panel as shown below. * Use a pointed object to change the ON/OFF settings of the MODE switches. Order of Priority The control input pins have a priority order. The priority order is as follows: 29 Controlling the AR-200R from an External Device (Control Input Connectors) Assigning Phrases to the Terminals Assign phrases 1 through 9 to Port Nos. 1 through 9. Settings in Effect When a Card Is Formatted fig. inp-13 "Important Notes on Making Connections and Switching the Power On and Off" (p. Phrase 1 0001 2 0002 3 0003 4 0004 5 0005 9 0009 Operational Specifications for Direct Playback (Last-In) Basic Operation of Direct Playback (Reverse Priority) fig. inp-10 Playing Back Phrases Assigned to the Connectors (Direct Playback) What Is Direct Playback (Reverse Priority)?/Use and Applications By inputting control signals directly to Port Nos. This is very convenient when you want to specify a desired phrase directly using a switch, relay, sensor, or other such means. fig. inp-08 Port No. 2 STOP Port 0002 0001 AUDIO OUTPUT 0001 Interrupted Playback: Input control signals to Port Nos. This stops playback of the phrase. A Control Signal A Control Signal A Control Signal A Control Signal A Control Signal A Control Signal 2 3 4 5 Port No. 1 Phrase 0001 0002 0003 0004 0005 9 0009 "Operational Specifications for Control Input Playback" (p. 28) Priority Order The most recently input control signal is given priority in playback. If a new and different control signal is input during playback of a phrase, playback of the current phrase is stopped, and playback of the specified phrase then begins. fig. inp-11 Connecting External Devices Connectors Used for Direct Play (Last-In) (Control I/O Connector) 1 through 9: Inputting a control signal directly to the connector with the number corresponding to the phrase starts playback of the phrase. In addition to the connectors just described, shorting the "11/12 (GND)" (ground) connectors enables "On. " fig. inp-09 Port No. 1 Port NO. 2 0001 0002 AUDIO OUTPUT 0001 Interrupt STOP 10 9 Select a Phrase 1 1 2 COM Playback is repeated while the control signal is continuously input. fig. inp-12 Port No. 1 12 11 COM 0001 AUDIO OUTPUT 0001 0001 * Control Input and DC Input Terminal (CONTROL A) "1, 2" are connected in parallel with Control I/O Connector (Control B) "1, 2. " 30 Controlling the AR-200R from an External Device (Control Input Connectors) AR-200R Settings Selecting the Control Input Mode Set the MODE switches on the AR-200R's bottom panel to select "DIRECT PLAYBACK" from the control input modes (PLAYBACK BY CARD DATA/DIRECT PLAYBACK/ BINARY PLAYBACK/INTERVAL PLAYBACK). You cannot achieve control input playback merely by connecting a device to the port. Be sure to set the control input mode and match the method used for connecting to the connectors. fig. inp-14 Binary Specification Port No. 1--8 87654321 01110000 START SIGNAL Phrase 112 PLAY * To conduct Binary Playback, you will need to obtain a control device capable of generating binary signals. * Input of binary specifications should be completed in no more than 50 milliseconds. Connecting External Devices Connectors Used in Binary Playback "1­8": Phrases are specified in binary format using combinations of 0 (Off) and 1 (On). In addition to the connectors just described, shorting the 11/ 12 (GND) (Ground) connectors enables "On. " fig. inp-15 Procedure for Setting the Control Input Mode 1. Set the MODE switches on the AR-200R's bottom panel as shown below. * Use a pointed object to change the ON/OFF settings of the MODE switches. Applications START Select a Phrase STOP 10 9 8 1 Assigning Phrases to the Terminals Assign phrases 1 through 9 to Port Nos. 1 through 9. Settings in Effect When a Card Is Formatted fig. inp-13 12 11 Port No. Phrase 1 0001 2 0002 3 0003 4 0004 5 0005 9 0009 GND Specifying Phrases in Binary Notation (Binary Playback) What Is Binary Playback?/Use and Applications By inputting binary (Base 2) signals to Port Nos. [. . . ] When reception of this packet is completed, the AR-200R changes to the current (currently displayed) phrase number. (AR-100/2000 compatible) Address(H) SIZE(H) DATA(H) Parameter Description =================================================================== 01 00 00 00 00 02 00 - 07 Phrase Number upper 3bits 01# 00 - 7f Phrase Number lower 7bits =================================================================== Phrase number DATA(H) A0001 - A0500 00 00 - 03 73 Appendices * * Only received packet data. When reception of this packet is completed, the AR-200R changes to the current (currently displayed) phrase number. Exclusive Address Table Recording Settings Address(H) SIZE(H) DATA(H) Parameter Description =================================================================== 01 00 10 00 00 03 00 - 07 Phrase Number upper 4bits 11# 00 - 7f Phrase Number lower 7bits 12# 00 - 02 REC Source 0:ANALOG-IN 1:DIGITAL-IN 2:MIDI-IN =================================================================== Phrase number DATA(H) A0001 - A1000 * * 00 00 - 07 67 Only received packet data. When reception of this packet is completed, the AR-3000 goes into REC PAUSE mode. However, if a phrase has already been saved, the AR-3000 deletes that phrase and goes into REC PAUSE mode. 63 MIDI Implementation Chart AUDIO RECORDER Model AR-200R Date : July. 1, 2006 MIDI Implementation Chart Transmitted Recognized Version : 1. 00 Remarks Media Player Section Function . . . [. . . ]