User manual RIDGID TS24241

[. . . ] 76 2:1(5·6 0$18$/ , 1&+ &2175$&725 6(5, (6 %(/7 '5, 9( 6$: )RU <RXU 6DIHW\ Part No. SP6250 5HDG DOO LQVWUXFWLRQV FDUHIXOO\ Printed in U. S. A. Table of Contents Section Page Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety Signal Words . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Before Using The Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Tighten adjusting nut until fence clamp just barely touches rear guide bar. This should provide the best fence adjustment possible without over tightening. Recheck fence parallelism with miter slot in locked position and adjust if necessary. If the fence does not clamp the same across the entire length of the bars, the guide bars may need to be readjusted with shims provided. Adjusting Nut Rear Guide Bar Fence Clamp and Rear Guide Bar Should Barely Touch When Fence is Raised Fence Clamp Adjusting Fence Indicator 1. Place rip fence on saw table so that it lightly touches the right side of the blade and lock it in this position. Adjust the indicator so that the red line is located over the "Zero" line of the right rip scale and tighten screw. Indicator at "Zero" Line 28 Installing Blade Guard 1. From the bag labeled "Blade Guard" remove the following parts: 2 Hex Head Screws, 1/4-20 x 5/8" Long 2 Hex Nuts, 1/4-20 2 Lockwashers, 1/4 External Type 1 Thumb Screw 1 Spreader Support From the blade guard carton find the following: 1 Blade Guard 2. Attach spreader to spreader support so that the edge of the spreader is even with the edge of the spreader support as shown. Insert a large set screw wrench in the notches of the pawls to hold the pawls out of the way. Tighten both hex head screws. 1/4-20 x 5/8 In Hex Hd Screw 1/4 In. External 1/4-20 Hex Nut Lockwasher Thumb Screw Spreader Support Blade Guard 1/4-20 Hex Head Screw Spreader Align Edges Spreader Support Lockwasher Hex Nut Square Blade Guard Support Cradle Hex Hd. Screws Pin in Notches of Support Spreader Rod Located in Blade Guard Support Thumb Screw 29 Assembly (continued) Aligning Blade Guard 1. Loosen socket set screw in guard support and move spreader left or right so that it touches blade of square. NOTE: The spreader is now square with the table and approximately in line with the sawblade. The spreader requires further adjustment to align it parallel to the blade and in the middle of the cut (kerf) made by the sawblade. IMPORTANT: To work properly, the spreader must always be adjusted so the cut workpiece will pass on either side of the spreader without binding or skewing to the side. NOTE: The spreader is thinner than the width of the cut (kerf) by approximately six thicknesses of paper. Anti-Kickback Pawls Set Screw Wrench Spreader Straightedge Along Side of Blade Socket Set Screw In Guard Support Space Equal to Approx. Make two folds in a small piece (6 x 6 inch) of ordinary newspaper making three thicknesses. The folded paper will be used as "spacing gauge". Spreader Looking Down on Saw Paper 4. Carefully move it against blade so that it is parallel to the blade, and just touches tips of saw teeth. Using 7/16 wrench loosen the 1/4-20 hex head screws so the spreader can slide sideways. [. . . ] TS24241 RIDGID parts are available on-line at www. ridgidparts. com Figure 6 - Guard Assembly 4 1 5 3 1 2 12 7 11 1 6 7 1 6 8 10 8 9 Always Order by Part Number - not by Key Number Key No. 826519 60208 62391 803528-1 826466 62390 805552 62520 813146-1 804845-1 62410 803422-163 62519 509507 Description Guard Asm. Complete Nut Push Pin 1/4 x 1-1/2 Support, Guard Guard, Saw Pin, 1/4 x 1-3/4 * Washer, 17/64 x 5/8 x 1/16 Spacer, Pawl Pawl Spreader Blade Pin, 1/4 x 1 * Pin, Roll 3/16 x 15/16 Spring, Pawl Bag Asm, Guard * Standard Hardware Item - May be purchased locally ­ Items Not Shown 64 Repair Parts Parts List for RIDGID 10 Inch Table Saw Model No. TS24241 RIDGID parts are available on-line at www. ridgidparts. com Figure 7 - Leg Set 3 2 1 11 15 16 5 17 2 2 9 8 14 10 14 4 15 2 6 7 3 8 7 6 9 12 1 12 13 Key No. [. . . ]