User manual RICOH MP7320A

[. . . ] Please take notice that the manufacturer will bear no responsibility for direct or indirect damages caused by the use of this product or its malfunction. Please take notice that the manufacturer will bear no responsibility for damage to data caused by this product. Please backup (copy) all important data as protection against data loss. q q q q q q PC DOS is a trademark of IBM Inc. MS-DOS, Windows, Windows ® 95, Windows ® 98/98SE, Windows ® Me, Windows NT®, Windows® 2000, Windows® XP*1 are trademarks registered in the United States and other countries by the Microsoft Corporation. [. . . ] PC Operating System IBM PC/AT compatible Windows Me/98/98SE/95(ORS2 or later) Windows NT Workstation Ver. 4. 0 (Service Pack 5) or later Windows 2000 (Professional) Windows XP*1 Pentium 166 MHz or higher (When using JustLink) 64MB or more Hard disk with average access time of 19msec or less, and data transfer speed of 2, 500KB/sec or greater. Enhanced-IDE interface (as Primary Slave, Secondary Master, or Slave) 5. 25-inch half height bay required +5V/+12V power socket required Recommendation Tested to be compatible Taiyo Yuden, Mitsui Chemicals, Mitsubishi CD-R Ricoh Chemical, Maxell CD-RW Ricoh Mitsubishi Chemical*2 High Speed CD-RW Ricoh Mitsubishi Chemical CPU Memory Hard disk Interface Drive bay Power Recommendation media*3 *1 *2 *3 For information on Windows XP supports, visit Ricoh's Web site The media written using the CD-R/RW drive may not be readable by CD-ROM drives. Even if it is the recommendation disc, some of discs may have possibility to fail writing with highest writing speed with the problem on the disc. In this case, please try to write with lower writing speed, or please try to use another disc. Multi-read compatible (Random UDF compatible) drives are: q q Drives that can read low reflectivity discs. Drives that support Packet Write. Front Panel Rear panel Front Panel 1. Disc tray This is the tray for the disc. Place the disc on the ejected disc tray, then lightly push the tray (or push the eject button) and the disc will be mounted. Caution Don't use force to pull out or push in the disc tray. This might cause damage to the loading section of the drive. 2. Headphone jack This jack is for connecting headphones or mini-speakers. 3. Volume control This is used to adjust the output volume of the headphone jack. It can't be used to adjust the output volume for the audio output connectors on the rear panel. Caution Turn the volume down before turning on the power. Sudden loud noises can damage your hearing. 4. Busy indicator The indicator stays green when the medium is being accessed or being read. Or, it stays red during the writing time, or stays orange when the drive is in the wait state. 5. Eject button This is the button used to eject or insert in the disc tray. 6. Emergency eject hole This drive has a function that allows the disc to be ejected manually if this becomes necessary in an emergency such as failure of the drive or a power outage. Caution This feature is a last measure to be used only in an emergency. Using it excessively will cause malfunction. Rear panel 1. Digital Audio Output Connector Provides output to a sound card (Digital signal). * No dedicated digital audio cable is supplied with the MP7320A. 2. Analog Audio Output Connector Provides output to a sound card (Analog signal). 3. Jumper Connector This jumper determines whether the drive is configured as a master or slave. Changing the master-slave configuration takes effect after power-on reset. 4. IDE Interface Connector Connect to the IDE (Integrated Device Electronics) interface using a 40-pin flat IDE cable. Caution Do not connect or disconnect the cable when the power is on, as this could cause a short circuit and damage the system. Always turn the power OFF when connecting or disconnecting the cable. Caution Be careful to connect with the proper way. Cannot be used (for writing or playing) with irregularly shaped discs (business card-sized, heart-shaped, etc. ) (* you can not use the drive with a CD adapter. ) Back Load the disc Emergency Eject Disc ejection Using the Drive in a Vertical Position Specific knowledge of hardware and software is necessary to install the drive. We cannot guarantee against direct or indirect damage resulting from improper connections. Ask your supplier for details of the installation procedure. Before Installation Before installing the drive, please note the following points. q You will need the following: r A Phillips head screw driver of a suitable size to fit the securing screws for the drive unit. r The manual for the computer, to know the location of the IDE connector. q Turn off all peripheral appliances of the computer, and the computer itself, and disconnect their power cords from the wall sockets. q Discharge any static electricity by touching the computer covers etc. [. . . ] Device Drivers Caution When using CD-ROM media, CD-R media or CD-RW media, do not attach any stickers or labels to the media. Using media with labels attached not only causes read and write errors, but data on the disc may be lost due to damage to the media itself. q q q q Load the disc Disc ejection Emergency Eject Using the Drive in a Vertical Position Drive : MP7320A Type Interface Data buffer memory Data transfer speed CD-RW/High Speed CD-RW Write/Read speed (Ave. ) Internal type Enhanced-IDE (ATAPI) 8MB 33MB/sec. (Max. ) (Ultra DMA mode2) Read Speed 4X: 8X: 20X: 32X: 40X: Write Speed CD-R: 8X: 16X: 32X: CD-RW: 2X: 4X: 10X: 120msec. or less horizontal/vertical (eject button upper) Format CD-DA CD-ROM CD-Extra CD-ROM XA Photo CD*3 *4 CD-i*3 *4 Video-CD CD-Text Loading system Tray type (automatic loading/eject) Write Read Play*2 600KB/sec. [. . . ]