User manual RICOH MP7063A

[. . . ] CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Akustischer Geräuschpegel Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Dieser Druckerüberschreitet einen Geräuschpegel von 70 dB (A) während dem Betrieb nicht. Declaration of Conformity "The Product complies with the requirements of the EMC Directive 89/366/EEC and the Low Voltage Directive 73/23/EEC. " · · · · Please take notice that the manufacturer of this equipment does not offer any warranty against data loss due to inappropriate installation or handling, or direct or indirect damages. Please take notice that the manufacturer will bear no responsibility for direct or indirect damages caused by the use of this product or its malfunction. [. . . ] Windows NT Workstation Ver. 4. 0 and Windows 2000: 64MB or more recommended Hard disk with average access time of 19msec or less, and data transfer speed of 1, 200KB/sec or greater. 150MB or more free space. (The free space needed for writing depends on the quantity of data. ) Enhanced-IDE interface (as Primary Slave, Secondary Master, or Slave) 5. 25-inch half height bay required +5V/+12V power socket required CD-R: CD-RW: *1 Ricoh, Mitsubishi Chemical, Taiyo Yuden, Mitsui Chemicals, TDK and Kodak discs Ricoh and Mitsubishi Chemical discs*1 CPU Memory Harddisk Interface Drive bay Power Recommendation discs The disc written using the CD-R/RW drive may not be readable by CD-ROM drives. Multi-read compatible (Random UDF compatible) drives are necessary. Multi-read compatible (Random UDF compatible) drives are: · · Drives that can read low reflectivity discs. Place the disc on the ejected disc tray, then lightly push the tray (or push the eject button) and the disc will be mounted. Headphone jack This jack is for connecting headphones or mini-speakers. 3. Volume control This is used to adjust the output volume of the headphone jack. It can't be used to adjust the output volume for the audio output connectors on the rear panel. Busy indicator This indicator lights green when a disc is mounted into the drive. If a disc is not mounted, the indicator does not light even when the power is turned on. When a illegal disc is loaded or some hardware trouble occurs, the indicator blinks. 5. Eject button This is the button used to eject or insert in the disc tray. 6. Emergency eject hole This drive has a function that allows the disc to be ejected manually if this becomes necessary in an emergency such as failure of the drive or a power outage. Caution This feature is a last measure to be used only in an emergency. Analog Audio Output Connector Provides output to a sound card (Analog signal). 2. Jumper Connector This jumper determines whether the drive is configured as a master or slave. Changing the masterslave configuration takes effect after power-on reset. 3. IDE Interface Connector Connect to the IDE (Integrated Device Electronics) interface using a 40-pin flat IDE cable. Caution Do not connect or disconnect the cable when the power is on, as this could cause a short circuit and damage the system. Always turn the power OFF when connecting or disconnecting the cable. 4. Power Connector Connects to the power supply (5 and 12V DC) of the host computer. Connecting the wrong way may damage the system (and is not guaranteed). 8 Specific knowledge of hardware and software is necessary to install the drive. We cannot guarantee against direct or indirect damage resulting from improper connections. [. . . ] (Max. ) (PIO4 or DMA2) 32X: 32X: 20X: 20X: 20X: 8X: 8X: 6X 6X: 4X: 4X: 4X: 2X: 2X: 2X: 1X: 1X: 1X: 4. 8MB/sec. (CD-DA) Average access time Initial processing time Mounting direction 120msec. or less horizontal/vertical 27 Compatible formats Format CD-DA CD-ROM CD-Extra CD-ROM XA Photo CD*3 *4 CD-i*3 *4 Video-CD *4 CD-Text Write Read Play*2 * * * * * * * * * * * * * * * * * * Loading system Power Power consumption Weight Dimensions Reliability Tray type (automatic loading/eject) DC5V, DC12V 12w max. 146 X 195 X 41. 3mm Error Rate: MTBF: MTTR: 10-12 bits or less 100, 000hours or greater Within 30 minutes When operating Temperature Humidity Vibration Shock 5°C to 40°C (No air cooling) 55% to 90% R. H. [. . . ]