User manual REVOX B77 SERVICE INSTRUCTIONS

[. . . ] You can download the new Multiroom Planner V2. 00 free-ofcharge from the download area of the Revox Homepage, under www. revox. com. 1 Introduction M203 Switching between stations using the Revox wall-mounted keypad* The M203 offers the option of selecting specific stations using the skip keys (<>) on an M218 wall-mounted keypad, once the TV tuner has been selected. This comfort function requires two settings: Note: Monitor-only devices This comfort function is only available with TV models with an integrated TV tuner. It cannot be selected in case of monitor-only devices without a TV tuner. 1/2 Audio IN assignment 2/2 TV Tuner assignment M51 in combination with M203 The sound input, e. g. TV, Aux1, Optical, etc. , of the remote device must be assigned to one of the following Remote buttons in the Remote menu: · Local · Local 1 · Local 2 · Local 3 M203 Setup #2 - Input The second assignment affects Setup #2 in the M203. [. . . ] The M203 Interface is also suitable as an interface to domestic facility management systems such as AMX or Crestron, which have a special Revox protocol. Even a Windows PC with the M230 control program can be connected to the serial interface on the M203. Connection: M203 with IR controller Socket: IR-Link Setup: M219: Yes M203 The connection to an IR receiver or a wall-mounted remote control is done through the 3pin, screw-fixable Phoenix plug connection. Revox recommends the use of a 2-core screened cable (microphone cable), where the screening is used as ground. Please ensure that you use the correct polarity when setting up as otherwise you might damage your equipment. 20V (DC) IN IR Signal Ground The maximum number of IR receivers that can be switched in parallel per M203 is 3. 5 Installation & Connection M203 Setup key Setup #1 Function: Display: Connection: M219: a) Slot M51 Addr. page 11) A different address must be assigned through the slot address, if a second M203 (M200) is connected to the M51 Link output, so that both don't occupy the same slot address. In the case of a double address assignment, neither of the two M203s (M200s) would be shown in the Version list. Slot address: #11 or #12 The two slot addresses 11 and 12 are available for selection. The following message appears if the selected address is already assigned: Using the Setup key, you call up the M203 menu, which is shown in the M51 display. If the M203 interface is connected with an M219 Additional room amplifier, the M51 display is also used. If there is no assignment, the HDMI input that was last selected remains active. Setting is done on page #2 in the M203 Setup Product features: - 4 HDMI inputs (4x1, 4x2) - 6 HDMI inputs (6x2) - 1 HDMI outputs (4x1) - 2 HDMI outputs (4x2), whereby both outputs can be operated in parallel - Resolution up to 1080p - HDCP-enabled - Optical audio digital output A crossed Sub-D cable is required for the transmission. Connection type: Plug-Plug For this reason, you should use the enclosed crossover adapter and gender adapter with the supplied Revox cable. M203 9-Pol Pin 2 Pin 3 Pin 5 9-Pol Pin 3 Pin 2 Pin 5 Max. This guarantees that important 2 minute run-on phase of the fan is always adhered to, even when an operation was carried out that would have bypassed it. M710 Projector switching times: Power-OFF 10 sec. Alternating source* Autostandby : ON Changing DISC From DVD to CD 60 sec. 60 sec. Plasma-TV 42 HD * Turning from a video source to a pure audio source. 16 Configuration M203 Setup #2 ­ AV Assignment Function: Display: Connection: M219: AV Assignment Source RS232 Yes 1. Selecting audio source To start with, select the M51 / M219 audio source that later should activate a particular video input on the Revox television/ HDMI Switcher, using the Source ± softkey. Unknown audio sources "Sources unknown" can still be present during the initial configuration, caused by the swap or the de-installation of modules. Following switch-on, it can take a few seconds until the M203 interface has identified all the M51 / M219 sources and until the Source "Unknown" message disappears. Any remaining unknown sources should be deleted by pressing the Disable softkey twice and then pressing the Delete softkey. If too many unknown sources are present, we recommend completely resetting the M203 interface by pressing the Disable softkey for several seconds, until Page #1 automatically appears. Using the Source+ and Sourcesoftkeys, you can step forwards and backwards respectively, through a loop of audio inputs, which are currently available on the M51 / M219. If the name of an audio source has been changed, the modified name also appears in the list. You will find more information about this in the previous section. 17 Configuration Intelligent Audio Sources The M200 differentiates between 3 type of audio sources: 1. [. . . ] Assigning video inputs In the second step, a video input from the television / HDMI Switcher is assigned to the selected M51/ M219 audio source, using the Input ± softkey. Using these softkeys, you can step through a loop of video inputs that are available to the television. The following display appears, if a video input is called by one or more audio sources: Assignment example As the televisions that can be selected from have different video inputs, only those video inputs that the corresponding TV device has, are actually displayed. The softkey Store appears as confirmation each time the Input is changed. [. . . ]