User manual REVOX A700

[. . . ] Please refer also to page 13 ff. Introduction M200 Mk2 M200 - New features - Switching between stations - Function overview Installation Connection M51 Link IN/ OUT RS 232 Trigger Input: Input A/ B Relay A/ B Voltage ramp 0-10V IR-LINK Setup Button Setup #1 ­ Trigger input Setup #2 ­ Relay Setup #3 ­ IR Address/ Source Setup #4 ­ Slot/ Serial Port Mode Serial Interface RS-232 Link RS-232 Filtered Video Controller Connection plan Revox Devices with M51 Revox Devices with M219 Gefen HDMI Switcher with M51 Gefen HDMI Switcher with M219 Overview Video products Gefen HDMI Switcher 4x1/ 4x2 / 6x2 Revox Video products Setup #5 AV Assignment Assigning audio source Smart audio sources Assigning video sources Setup #5 ­ TV-Lift Disable Assignment Setup #5 Reset Assignment Guarantee Included in delivery Technical data Wiring the M200 interface Introduction Introduction Introduction 1 2 2 3 3 4 4 5 6 6 6-7 8 9-12 12 12 12 13 14 14 14 15 16 17 17 18-19 20 20 21 22 22 24 24 25 25 26 27 Introduction M200 Mk2 New features from software V2. 00 From software version 2. 00, the M200 can be connected not only to an M51 but also to the M219 Side room amplifier. As a result, a Revox television can also be controlled from an side room, using the M219 Side room amplifier. The option of connecting an M200 interface to an M219 exists with the first four Side room amplifiers for each zone. As a result, a total of 16 Side room amplifiers can be connected with an M200 interface in a Revox Multiroom system with 4 different zones. [. . . ] voltage 12-20V (DC) IN IR Signal Ground Important Relay control through the IR remote control (Relay function: Remote), is only possible if the IR Receiver, e. g. M204, M208 is directly connected to the M200 through the IR Link - see drawings on pages 14-16. The maximum number of IR receivers that can be switched in parallel per M200 is 3. M200 Mk2 5 Configuration M200 Mk2 Setup Button Setup #1 ­ Control Input Function: Display: Connection: M219: Trigger input Control Input A/B Input A/B - page 4 No Using the Setup key, you call up the M200 menu, which is shown in the M51 display. If the M200 interface is connected with an M219 Side room amplifier, the M51 display is also used. In the case of an M10 installation, display is done using the M230 service program or M-Scope. Using INPUT A and INPUT B, you can trigger specific events at the M51. The required option can be selected from an option loop by pressing the Input und Input softkeys. Using the Softkeys you can get to pages #1 till #5. Setup page #5 only appears if a video device has been selected on page #4 as Serial Port Mode. DVD/CD Tuner Tape Aux 1-3 Local TV Video 1-6 Power On Power Off System Off Mute (Toggle)* Light Dimmer Not Used 6 Configuration DVD/CD - TV M51 is switched on with and/or switches over to the corresponding source. System Off Switches the complete system off, including any side rooms. Mute (Toggle) This toggles the mute function of the M51 and is only possible in conjunction with the 5. 1 Decoder Module MK 2 or 3. Light Dimmer Activates the voltage output dimmer function (Output 0-10V) with Toggle-Automatic. Not Used Deactivates the corresponding input. M200 Mk2 Please note When you are selecting the source, you should be aware that the source that has been assigned to the corresponding button in the Remote menu will be selected. This page enables you to selectively switch on and/or between video inputs on a Revox device or an HDMI Switcher from the Gefen company, dependant on the selected M51/ M219 source. M200 Mk2 The convenient integration can of course also be used for the M51's integrated DVD player. Please refer to the picture on the next page ­ Connection : Video 1). The audio source and video input links referred to in the example are defined in Setup #5. You will find an exact description of the links, starting from page 21. Complete reset? Example M200 with M51: A SAT receiver can conveniently be integrated through the automatic selection of the video input on the TV by the M51. Its picture output is connected, for example, to the YC input on the Revox TV, while the audio signal is connected to the Optical digital input on the M51. If you now select the source SAT (Optical) at the M51, the Revox TV automatically transmits the SAT receiver picture over the Input-2 and the sound from the SAT receiver is transmitted over the M51. Yes You should always carry out a complete reset with each new configuration as well as when changing to another TV model. To do this, press the Disable softkey on Setup page #2 and keep it pressed, until the system automatically returns you to page 1. No A complete reset is not necessary with an assignment change within a TV model. 13 Configuration M200 Mk2 Connection plan: Revox TV with M51 Connection plan: Revox TV with M219 * Adapter is model-dependent, see page 18 14 Configuration M200 Mk2 Connection plan: HDMI switcher with M51 Note The HDMI output on the M51 is only available if the DVS module is installed. ® Gefen : Registered trademark of the Gefen Company/ US 15 Configuration M200 Mk2 Connection plan: HDMI switcher with M219 16 Configuration Gefen HDMI Switcher 4x2, 4x1 Switcher 6x2 Control software for the HDMI Switcher from the Gefen Company (www. gefen. com) The HDMI inputs on the HDMI switcher are activated, dependant on the M51/ M219 source. If there is no assignment, the HDMI input that was last selected remains active. Setting is done on page #5 in the M200 Setup Product features: - 4 HDMI inputs (4x1, 4x2) - 6 HDMI inputs (6x2) - 1 HDMI outputs (4x1) - 2 HDMI outputs (4x2), whereby both outputs can be operated in parallel - Resolution up to 1080p - HDCP-enabled - Optical audio digital output A crossed Sub-D cable is required for the transmission. Connection type: Plug-Plug For this reason, you should use the enclosed crossover adapter and gender adapter with the supplied Revox cable. M200 Mk2 9-Pol Pin 2 Pin 3 Pin 5 9-Pol Pin 3 Pin 2 Pin 5 Max. [. . . ] If, for example, the video input from the Server was activated at the television using the remote control, the television is automatically activated next time this source is selected. M200 Mk2 3. Intelligent sources In the case of intelligent sources, it is a question of sources, which, dependant on setting or medium, can transmit a video signal to accompany the audio signal. If there is a music CD on the M51 drive, the television is not switched on because in this case, no video is required. If, on the other hand, a DVD is identified, the television is switched on. [. . . ]