User manual RENKUS-HEINZ X310 TSC CONTROLLER

[. . . ] Refer all servicing to qualified personnel VORSICHT GEFAHR EINES ELEKTRISCHEN SCHLAGES: NUR VON QUALIFIZIEREM WARTUNGSPERSONAL ZU ÖFFNEN Eindrigliche Warnung: Wartungsvorschriften dienen nur der Benutzung durch qualifizieres Personal. Zur Vermeidung eines elektrischen Schlages keine anderen als die in den Betriebsvorschriften beschriebenen Wartungsarbeiten ausführen, es sei denn Sie sind dafür qualifiziert. Wartungsarbeiten sind nur von qualifiziertem Wartungspersonal auszuführen. 2 X310 TSC CONTROLLER · X14 · X24 OWNER'S MANUAL Table of Contents Warning Messages Table of Contents Introduction Overview System Wiring Diagrams X310 TSC CONTROLLER X14 X24 Plug-In Modules Front Panel Features X310 TSC CONTROLLER & X24 Status Indicators X14 Status Indicators Rear Panel Features X310 TSC CONTROLLER & X24 Sense Lines X14 Sense Lines Set-Up Mounting Cabling Amplifier Selection Sense Connectors Trouble Shooting Technical Specifications 2 3 4 5 6 7 8 9 10 10 11 11 12 12 13 13 14 14 14 14 15 16 3 X310 TSC CONTROLLER · X14 · X24 OWNER'S MANUAL Introduction Congratulations on your purchase of a Renkus-Heinz loudspeaker controller. It has been designed to provide years of trouble-free, high performance operation. [. . . ] When the Channel 1 input is connected directly to the Mixer output, the output of the subwoofer and the 2-way loudspeaker will overlap and produce a "bump' in the frequency response. This overlap can be eliminated by using the Channel 2 FR/HF output to drive the Channel 1 input. The FR/HF output is band limited to match the subwoofer's crossover point. When the Channel 2 FR/HF output is used in this fashion, the + & - HF pins on the Channel 2 Sense Line connector must be shorted together!Whenever a pair of Sense Lines are not used, it is common practice to short them together to prevent their associated red LED warning lights from being "on" constantly. Highs Lows Power Amplifier Subwoofer Power Amplifier 2-Way Active Loudspeaker Figure 7 Typical wiring for a X24 used with 2-way active loudspeakers and a subwoofer. 8 X310 TSC CONTROLLER · X14 · X24 OWNER'S MANUAL Plug-In Modules To insure the highest possible loudspeaker performance while still providing optimum protection for the loudspeaker, each Renkus-Heinz controller is specifically configured for a particular Renkus-Heinz loudspeaker model. This configuration is accomplished by three "plug-in" PC boards or modules used inside the controller. The combination of these three boards is unique for each loudspeaker model. SUB/LF (Subwoofer / Low Frequency) Sense Fail Indicator: This red LED will indicate if the sense line coming from the output of the SUB/LF amplifier has become disconnected. If the sense line becomes disconnected, the controller will mute the output audio for the SUB/ LF channel. SUB/LF (Subwoofer / Low Frequency) Protect Indicator: This red LED will indicate the operation of the speaker protection circuitry. This LED will illuminate because of any one or combination of the following reasons: 1. Thermal protection activated. 11 X310 TSC CONTROLLER · X14 · X24 OWNER'S MANUAL Rear Panel Features AC Receptacle / Fuse Holder: This receptacle accepts an IEC 320/CEE-22 AC power connector. A line cord with the appropriate matching connector is supplied with the controller. Before plugging in the AC power cord, make sure the AC voltage selector switch is set to the correct position. An incorrect setting of the AC voltage select switch may result in unit failure. The fuse can only be accessed by first unplugging the AC power cord from the AC receptacle. When the fuse drawer is opened, the innermost fuse is the active fuse, the outer fuse is a spare fuse. AC Voltage Selector Switch: This switch allows the controller to be configured for the appropriate AC line voltage. Use the 115VAC position for AC line voltages ranging from 100 to 120VAC. Use the 230VAC position for voltages ranging from 220 to 240VAC. INPUT SUB/LF OUT FR/HF FROM AMP OUTPUT SENSE AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN _+_+ PIN 1 = GND PIN 2 = PIN 3 = 115V LF HF + _ WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. MODEL X310 TSC CONTROLLER IRVINE, CALIFORNIA MADE IN USA RENKUS-HEINZ INPUT CHANNEL 2 PIN 1 = GND PIN 2 = PIN 3 = SUB/LF OUT FR/HF FROM AMP OUTPUT SENSE CH2 INPUT CHANNEL 1 SUB/LF OUT FR/HF FROM AMP OUTPUT SENSE CH1 AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN _+_+ + _ LF HF _+_+ 115V LF HF WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. MODEL X24 IRVINE, CALIFORNIA MADE IN USA RENKUS-HEINZ X310 TSC CONTROLLER & X24 Figure 7: X310 TSC CONTROLLER & X24 Rear Panels X310 TSC CONTROLLER and X24: The rear panels for the X310 TSC CONTROLLER and X24 are identical, except the X24 has two channels where the X310 TSC CONTROLLER has only one channel. The X310 TSC CONTROLLER and the X24 rear panels are shown above in Figure 7. Input: This female XLR connector is the audio input to the controller. [. . . ] HIGH- and HIGH+ (High Frequency): Connects to the high frequency channel amplifier output. X14 Sense Lines 13 X310 TSC CONTROLLER · X14 · X24 OWNER'S MANUAL Set-Up Mounting Mounting: For most applications, mount the controller in the amplifier rack. This will allow short sense cables from the amplifier to the controller. This also reduces the possibility of ground loops between the controller and the amplifier. Allow at least one rack space between the top of the amplifier and the bottom of the controller. [. . . ]