User manual RENKUS-HEINZ X-220 TSC CONTTROLLER

[. . . ] Refer all servicing to qualified personnel VORSICHT GEFAHR EINES ELEKTRISCHEN SCHLAGES: NUR VON QUALIFIZIEREM WARTUNGSPERSONAL ZU ÖFFNEN Eindrigliche Warnung: Wartungsvorschriften dienen nur der Benutzung durch qualifizieres Personal. Zur Vermeidung eines elektrischen Schlages keine anderen als die in den Betriebsvorschriften beschriebenen Wartungsarbeiten ausführen, es sei denn Sie sind dafür qualifiziert. Wartungsarbeiten sind nur von qualifiziertem Wartungspersonal auszuführen. 2 X12 · X14 · X-220 TSC CONTTROLLER OWNER'S MANUAL Table of Contents Warning Messages Table of Contents Introduction Overview System Wiring Diagrams X12 X14 X-220 TSC CONTTROLLER Plug-In Modules Front Panel Features X12 & X-220 TSC CONTTROLLER Status Indicators X14 Status Indicators Rear Panel Features X12 & X-220 TSC CONTTROLLER Sense Lines X14 Sense Lines Set-Up Mounting Cabling Amplifier Selection Sense Connectors Trouble Shooting Technical Specifications 2 3 4 5 6 7 8 9 10 10 11 11 12 12 13 13 14 14 14 14 15 16 3 X12 · X14 · X-220 TSC CONTTROLLER OWNER'S MANUAL Introduction Congratulations on your purchase of a Renkus-Heinz loudspeaker controller. It has been designed to provide years of trouble-free, high performance operation. [. . . ] This overlap can be eliminated by using the Channel 2 FR/HF output to drive the Channel 1 input. The FR/HF output is band limited to match the subwoofer's crossover point. When the Channel 2 FR/HF output is used in this fashion, the + & - HF pins on the Channel 2 Sense Line connector must be shorted together!Whenever a pair of Sense Lines are not used, it is common practice to short them together to prevent their associated red LED warning lights from being "on" constantly. Highs Lows Power Amplifier Subwoofer Power Amplifier 2-Way Active Loudspeaker Figure 7 Typical wiring for a X-220 TSC CONTTROLLER used with 2-way active loudspeakers and a subwoofer. 8 X12 · X14 · X-220 TSC CONTTROLLER OWNER'S MANUAL Plug-In Modules To insure the highest possible loudspeaker performance while still providing optimum protection for the loudspeaker, each Renkus-Heinz controller is specifically configured for a particular Renkus-Heinz loudspeaker model. This configuration is accomplished by three "plug-in" PC boards or modules used inside the controller. The combination of these three boards is unique for each loudspeaker model. Figure 4 shows the plug-in boards and their location on the main "mother" boards inside the controller. SUB/LF (Subwoofer / Low Frequency) Sense Fail Indicator: This red LED will indicate if the sense line coming from the output of the SUB/LF amplifier has become disconnected. If the sense line becomes disconnected, the controller will mute the output audio for the SUB/ LF channel. SUB/LF (Subwoofer / Low Frequency) Protect Indicator: This red LED will indicate the operation of the speaker protection circuitry. This LED will illuminate because of any one or combination of the following reasons: 1. Thermal protection activated. 11 X12 · X14 · X-220 TSC CONTTROLLER OWNER'S MANUAL Rear Panel Features AC Receptacle / Fuse Holder: This receptacle accepts an IEC 320/CEE-22 AC power connector. A line cord with the appropriate matching connector is supplied with the controller. Before plugging in the AC power cord, make sure the AC voltage selector switch is set to the correct position. An incorrect setting of the AC voltage select switch may result in unit failure. The fuse can only be accessed by first unplugging the AC power cord from the AC receptacle. When the fuse drawer is opened, the innermost fuse is the active fuse, the outer fuse is a spare fuse. AC Voltage Selector Switch: This switch allows the controller to be configured for the appropriate AC line voltage. Use the 115VAC position for AC line voltages ranging from 100 to 120VAC. Use the 230VAC position for voltages ranging from 220 to 240VAC. INPUT SUB/LF OUT FR/HF FROM AMP OUTPUT SENSE AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN _+_+ PIN 1 = GND PIN 2 = PIN 3 = 115V LF HF + _ WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. MODEL X12 IRVINE, CALIFORNIA MADE IN USA RENKUS-HEINZ INPUT CHANNEL 2 PIN 1 = GND PIN 2 = PIN 3 = SUB/LF OUT FR/HF FROM AMP OUTPUT SENSE CH2 INPUT CHANNEL 1 SUB/LF OUT FR/HF FROM AMP OUTPUT SENSE CH1 AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN _+_+ + _ LF HF _+_+ 115V LF HF WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. MODEL X-220 TSC CONTTROLLER IRVINE, CALIFORNIA MADE IN USA RENKUS-HEINZ X12 & X-220 TSC CONTTROLLER Figure 7: X12 & X-220 TSC CONTTROLLER Rear Panels X12 and X-220 TSC CONTTROLLER: The rear panels for the X12 and X-220 TSC CONTTROLLER are identical, except the X-220 TSC CONTTROLLER has two channels where the X12 has only one channel. The X12 and the X-220 TSC CONTTROLLER rear panels are shown above in Figure 7. Input: This female XLR connector is the audio input to the controller. [. . . ] HIGH- and HIGH+ (High Frequency): Connects to the high frequency channel amplifier output. X14 Sense Lines 13 X12 · X14 · X-220 TSC CONTTROLLER OWNER'S MANUAL Set-Up Mounting Mounting: For most applications, mount the controller in the amplifier rack. This will allow short sense cables from the amplifier to the controller. This also reduces the possibility of ground loops between the controller and the amplifier. Allow at least one rack space between the top of the amplifier and the bottom of the controller. [. . . ]