User manual RENKUS-HEINZ ICONYX IC LIVE ICL-FR-DUAL

[. . . ] Owners Manual Digitally Steerable Line Array Loudspeaker Systems IC Live ICL-R ICL-FR & ICL-FR-DUAL USERS MANUAL Assembly & Installation Instructions IC Live Users Manual. Models: ICL-R, ICL-FR & ICL-FR-DUAL IMPORTANT SAFETY INSTRUCTIONS 1. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on it. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] IC Live arrays can store up to 10 different configurations as Presets in the array's DSP memory. For example, you might optimize one configuration for small events on the main audience area and another for larger occasions when a balcony is used. The Presets include the beam steering data, as well as gain, EQ , compression, etc. They can be recalled from either the rear of the array, from the controlling computer or, if one is provided a wall mounted rotary switch. A digital readout on the rear of the array displays the selected Preset. They are labeled 10 to 19 for single arrays and 20 to 29 for Dual arrays. Presets 10 and 20 are claimed by the factory for field test purposes; they send an equal signal to all the drivers making it easy to check them by ear for proper operation. Portable IC Live models are also supplied with a number of preset configurations set at the factory for typical setups. IC Live users should refer to their Operators manual for details on these presets. If you attempt to leave Beam Steering without saving the setup information, the prompt shown here will remind you of the need to save it, if you want to keep it. In the beam steering window, select either Write to Device or Save as Preset. Write to Device will send the beam steering settings direct to the array''s DSP and write over any previous settings. Standard Preset numbers are 10 to 19 for single arrays and 20 to 29 for Dual arrays, with numbers 10 and 20 preset and locked at the factory to "flat" for aural testing purposes. On the Array's control panel selection of the desired Preset is controlled by three push buttons located directly below the digital readout. The Preset Up and Preset Down buttons are used to select the desired Preset and the Enter button used to enter the selection into the DSP. The readout display will pulse while the selected Preset's configuration settings are being entered into the DSP. In Dual arrays, the Preset UP, Preset Down and Enter buttons are disabled in the "Slave" module (the upper module). CONNECT MODE 31 IC Live Users Manual. Models: ICL-R, ICL-FR & ICL-FR-DUAL Control Mode provides access to the Loudspeaker Amplifier's internal DSP and allows you to control its settings. You can enter Control Mode by clicking on the CONTROL button at the top of the main workspace, or from within any loudspeaker's Properties window. Any or all of the Control functions can be restricted to authorized operators who have password access; more information on password authorization can be found in the Supervise Mode section of this manual. When you enter Control mode in the main workspace, the directory tree on the left remains the same. On the left, an On/Off button allows you to switch the amplifier(s) On or select Standby (Off) mode. [. . . ] It can also be downloaded free of charge from: ftp://ftp. renkus-heinz. com/Software/CNDisco342. exe or http://www. cirrus. com/dispatch/forms/sup/boardreg/breg/agree. jsp?agid=TB237&fp=/en/pubs/software/CNDisco345. exe Problem: I am attempting to do anything RHAON-related over a Wireless Access Point, or I am attempting to either control a RHAON network or pass audio over a WiFi link with no results Solution: Because of CobraNet bandwidth and latency concerns, RHAON (and CobraNet) will not work effectively over an 802. 11a/b/g/n WiFi link. 61 IC Live Users Manual. Models: ICL-R, ICL-FR & ICL-FR-DUAL FAQ and RHAON Network Troubleshooting Tips (Continued) Problem: My computer went to sleep with RHAON running and now I cannot communicate with my loudspeakers or see any of them on the network. Solution: The CobraNet Components may not be able to recover from sleep mode on some computers. To fix, close RHAON (and, if running, CobraNet Discovery) and bring up the Windows Task Manager (Ctrl-AltDelete). [. . . ]