User manual RCA RCU 900

[. . . ] RCU900_IB_revC. qxp 12/3/02 9:45 Page 1 Universal Learning Remote with TOUCHSCREEN User's Guide Limited 90 Day Warranty RCU900 remote RCU900_IB_revC. qxp 12/3/02 9:45 Page 2 Table of Contents Introduction . . 36 2 RCU900_IB_revC. qxp 12/3/02 9:45 Page 3 Universal Learning Remote with Touchscreen Congratulations on your purchase of the RCU900 by RCA. The RCU900 is one of the most sophisticated, yet easy to use, remote control units available today. With the RCU900, juggling multiple remote controls is a thing of the past! [. . . ] Press LCD CLEAR on the Main Setup Screen to exit Setup Mode. Smart Macro Key Operations Your RCU900's Smart Macro feature allows you to execute a sequence of commands with one keypress. A total of 20 Learned commands can be stored under each of the nine available LCD MACRO keys. The sequence of commands you want a Smart Macro to execute must be programmed in correct sequential order. Any sequence of commands that you regularly perform can be stored as a Smart Macro and reduced to a single keypress. You cannot program a Macro within a Macro. Program a Smart Macro Example of Programming a Macro 1. Now you're ready to record your favorite satellite program with just a press of a button. Gather all your original remotes that contain functions you would like to add to a Smart Macro. Point the top of the original remote at the base of the RCU900 so the IR LED on the original remote is in line with the RCU900 Learning sensor, located at the bottom of the remote. Press and hold the SETUP key on the rubber keypad until the LED indicator light remains on and the touchscreen shows the Main Setup Screen. The LED indicator light blinks once to indicate acceptance of the keypress. Press and release the digit key under which you want to store the Smart Macro (from 1-9). The LED indicator light blinks once to indicate acceptance of the keypress. The LED indicator light blinks once to indicate acceptance of the keypress. 19 RCU900_IB_revC. qxp 12/3/02 9:45 Page 20 Program a Smart Macro (continued) 8. Press and hold the key on the original remote until the LED indicator light on the RCU900 blinks once. Program additional commands in the order you want them to be stored in the Smart Macro. To add commands to the Smart Macro, repeat numbers 7 and 8 above, using original remotes to program. Note: It may be necessary to add a delay in between the Macro commands to allow your TV warm-up time. Delays can be added by pressing and releasing the SETUP key during the Macro Learn sequence. Press and release a digit key (1-9) to indicate the delay time required (1=1 second; 2=2 seconds; 3=3 seconds, etc. ). Any delay added to the Macro sequence is counted as one keystroke of the possible 20 keystrokes for a Smart Macro. You can store up to 20 Learned commands under one Smart Macro. Note: If a problem occurs with the Learning, the LED indicator light flashes for two seconds but remains in the Smart Macro routine. Once you are finished programming the Macro, press and release the LCD OK key. If you program all 20 keys into a Smart Macro, the Macro is automatically stored after the 20th learned command is completed. Execute a Smart Macro 1. [. . . ] D) Memory capacity is full (20 Learned commands for each of nine modes). E) Original remote might not be compatible with Learning procedure. Your VCR is not recording. You have trouble changing the channels on your TV. The LCD OK key is not responding. The Learning or Smart Macro processes cannot be completed successfully. 28 RCU900_IB_revC. qxp 12/3/02 9:45 Page 29 Code List Televisions Abex . . 075, 076, 077, 089, 133, 163, 165 29 RCU900_IB_revC. qxp 12/3/02 9:45 Page 30 Televisions (continued) Majestic . 087, 089, 133, 163, 183, 184, 205, 206, 207, 208, 212, 213 Philips/Magnavox . [. . . ]