User manual RCA RCU 410

[. . . ] SLEEP The SLEEP button allows you to set a time to turn off the TV automatically. L1, L2, L3, L4 The L1­L4 buttons are used for storing learned functions from other remote controls. LEARN The LEARN button allows you to "record" and "delete" learned functions from your remote control. Programming For TV 1. Press and hold the CODE SEARCH button until the INDICATOR LIGHT lights, then release the CODE SEARCH button. [. . . ] Press and release the CODE SEARCH button and the remote will return to original operation mode. All learned command functions under the device are now cleared. N A H C CODE SEARCH H C V EE R P UT M 2 CODE SEARCH INDICATOR LIGHT TV 1 5 INDICATOR LIGHT 3 FF ·O Y PLA LE B A C TV P STO D AR RW FO CH + USE PA R TE EN (BLINK) (BLINK) CODE SEARCH 4. Press and release the valid button to be learned on the RCA remote in which you will store a new function. The L1, L2, L3, L4, or other functions keys may be used in this programming mode. Press and hold the button on the original remote control until INDICATOR LIGHT on the RCA remote blinks once. Once the INDICATOR LIGHT blinks you may continue with the next function. If there is error in learning the new function the INDICATOR LIGHT will flash for 3 seconds but remain in the learning mode. Return to step 5 if the INDICATOR LIGHT flashed. NOTE: Hold the function key on your original remote for at least 3 seconds for the command to be successfully learned. Clearing All Learned Buttons or Functions This procedure will erase all learned functions in every device mode. This step is recommended when attempting any learning of a new function from a new remote. Press and hold the CODE SEARCH button until the INDICATOR LIGHT lights, then release the CODE SEARCH button. Press and release the CODE SEARCH button and the remote will return to original operation mode. All learned command entries are now cleared. CODE SEARCH CODE SEARCH INDICATOR LIGHT (BLINK) 7. Once the selected functions are stored press the CODE SEARCH button and the remote will return to original operation mode. 11 CODE SEARCH 12 RCU410MSL_IB 10/4/01 1:57 PM Page 14 Programming With Code Search If your TV, VCR, or Cable Box does not respond after you have tried all the codes for your brand, or if your brand is not listed, try searching for your code by following the steps below. Menu Functions The Menu is used to make changes such as setting color, channels, timers, etc. Press and hold CODE SEARCH until the INDICATOR LIGHT lights, then release CODE SEARCH. Press and release the device button for the device you are programming (TV, VCR or CABLE). The INDICATOR LIGHT will blink once then remain lit. Note: For AUX, press SAT·AUX then the device button you are assigning to AUX. CODE SEARCH INDICATOR LIGHT 1. The INDICATOR LIGHT will blink continuously to indicate the remote is now in Menu Mode. While in MENU these buttons will function as follows: VOL UP/DOWN buttons will operate as CURSOR RIGHT/LEFT. For RCA, GE an ProScan, pushing the MENU button will select the highlighted item. The numeric buttons may also be used to select the MENU choice. Note: Not all functions in competitive models and brands of televisions may be fully supported. (BLINK) (BLINK) 4. Press and release ON·OFF until your device turns off. Important: You may have to press ON·OFF up to 200 times. 5. When your device turns off, press the ENTER button, the INDICATOR LIGHT will go off. (OFF) Retrieving Codes If you need to find the three-digit code for your TV, VCR or Cable Box after your device is set-up using Code Search, use this procedure. Exiting the Menu Mode: To exit the Menu Mode and clear the screen push the DEVICE button on the remote. [. . . ] This warranty excludes defects or damage due to misuse, abuse, or neglect. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. © 2001 Thomson multimedia Inc. Socorro, TX 79927 PRCU410MSL Rev0501 Trademark(s) ®Registered Marca(s) Registrada(s) Made in China www. rca. com RCU410MSL_IB 10/4/01 1:58 PM Page 22 First Class Postage Required RCU410MSL Product Registration Please complete and return this Purchase Registration Card right away. This information will help us get to know and service our customers better. 1. [. . . ]