User manual RAYMARINE ST60+ GRAPHIC DISPLAY

[. . . ] ST60+ Graphic Display Owner's Handbook Document reference: 81268-2 Date: December 2005 Raymarine, ST60+ and SeaTalk are trademarks of Raymarine UK Limited © Handbook contents copyright Raymarine UK Limited 2005 i Preface Contents Important information Safety notices WARNING: Product installation & operation This equipment must be installed and operated in accordance with the Raymarine instructions provided. Failure to do so could result in personal injury, damage to your boat and/or poor product performance. WARNING: Electrical safety Make sure you have switched off the power supply before you start installing this product. WARNING: Navigational safety Although we have designed this product to be accurate and reliable, many factors can affect its performance. [. . . ] In track mode, to plot a track to the next waypoint, hold down the track button for 1 second. To leave track mode, press the track button again. 1. 7 Alarm messages The ST60+ Graphic Display supports a range of SeaTalk alarm signals and responds with an internal buzzer and an appropriate on-screen alarm message. In addition to this, the ST60+ Graphic Display can also provide external alarm signals for the Auxiliary Alarm option. The range of available alarms depends on: · What data is available on SeaTalk. · Which alarms are enabled during User calibration (see Chapter 4, Calibration ). 12 ST60+ Graphic Display Owner's Handbook Internal alarms The internal alarms are as follows: Message Meaning Deep or shallow anchor alarm Shallow water alarm Deep water alarm High wind speed alarm Radar guard zone alarm Lost fix alarm The battery voltage has fallen below the specified low-voltage level. ANCHOR ALARM (with current depth) SHALLOW ALARM (with current depth) DEEP ALARM (with current depth) HIGH WIND ALARM (with current wind speed) RADAR ALARM LOST FIX ALARM LOW BATTERY ALARM (with current voltage) External alarms An optional Auxiliary Alarm can be fitted at a convenient remote position, to give a loud, audible indication if any one of a range of alarms occurs. This option is particularly useful for situations where high ambient noise may make it difficult to hear the instrument's internal alarm (e. g. aboard a power boat). Note: An Auxiliary Alarm cannot be used if the NMEA OUT port is being used for NMEA data. Actions to take if an alarm occurs If an alarm occurs, investigate the cause immediately and if possible, take appropriate action to remove the cause. If an alarm message is displayed, use this to guide your course of action. Silencing internal alarms You can silence an internal alarm by pressing any one of the ST60+ Graphic Display front panel buttons. Remember though, that removing the alarm sound does not remove the cause of an alarm. If the alarm condition persists, the alarm will recur. Chapter 1: Operation 13 Silencing external alarms Most external alarms can be silenced only at the alarm-initiating device e. g. Exceptions to this are the LOST FIX ALARM and the LOW BATTERY ALARM , which can be silenced by pressing any of the ST60+ Graphic Display front panel buttons. 1. 8 Display settings Illumination When the instrument is first powered up, the display backlighting is set to its lowest (courtesy) level, to facilitate initial access to the buttons. Hold down the button for approximately 1 second, to enter the backlighting-adjust mode. Momentarily press the cycle through these levels until you reach the level you want. button to Note: The display will time out to normal operation 5 seconds after the last button press. 1 second D6434-1 14 ST60+ Graphic Display Owner's Handbook Contrast To adjust the display contrast: 1. While in backlighting-adjust mode, hold down the button for approximately 1 second, to enter the contrast-adjust mode. Use the track or reset button to set the contrast to the required level. Press the page button to leave the contrast-adjust mode. Note: The display will time out to normal operation 5 seconds after the last button press. 1 second LAMPS 1 second track reset Decrease contrast Increase contrast D6435-1 15 Chapter 2: Maintenance & Troubleshooting 2. 1 Maintenance Servicing and safety · Raymarine equipment should be serviced only by authorised Raymarine service technicians. They will ensure that servicing procedures and replacement parts used will not affect performance. · Some products generate high voltages, and so never handle the cables/connectors when power is being applied to the equipment. · When powered up, all electrical equipment produces electromagnetic fields. These can cause adjacent pieces of electrical equipment to interact with one another, with a consequent adverse effect on operation. In order to minimise these effects and enable you to get the best possible performance from your Raymarine equipment, guidelines are given in the installation instructions, to enable you to ensure minimum interaction between different items of equipment, i. e. [. . . ] This enables you to re-apply the factory settings if you want to reset the instrument to a known operating condition. · A self-test entry screen. 44 ST60+ Graphic Display Owner's Handbook Procedure To carry out Dealer calibration: 1. Hold down the and buttons together for approximately 12 seconds, to select the Dealer calibration entry page (see Dealer calibration diagram). Press the track and reset buttons together, to start Dealer calibration. [. . . ]