User manual RAYMARINE ST30 BIDATA (ROUND)

[. . . ] ST30 Round Bidata Owner's Handbook Document number: 81075_4 Date: 1st April 2001 Copyright © Raymarine Limited 2001 Preface i Important information WARNING Although your ST30 instrument is designed to give accurate and reliable performance, it should serve only as an aid to navigation and should never lead to the erosion of good seamanship. Always maintain a permanent watch and be aware of situations as they develop. EMC conformance All Raymarine equipment and accessories are designed to the best industry standards for use in the leisure marine environment. The design and manufacture of Raymarine equipment and accessories conform to the appropriate Electromagnetic Compatibility (EMC) standards, but correct installation is required to ensure that performance is not compromised. Handbook information To the best of our knowledge, the information in this handbook was correct when it went to press. However, the Raymarine policy of continuous product improvement may change product specifications without notice. [. . . ] These are set during basic calibration (see Chapter 4, Calibration). 2 ST30 Round Bidata Owner's Handbook 1. 2 Depth key functions The following flow chart shows the depth key functions. bidata depth speed depth speed WATER DEPTH SHALLOW ALARM OFFSET D1763-2 Water depth Depth is displayed in feet (0 to 400 ft) or metres (0 to 120 m). Shallow alarm The shallow alarm displays the depth (feet or metres) at which point audible and visual alarms will be triggered. These alarms can be silenced by pressing the speed or depth key. Adjusting shallow depth 1. From the shallow depth alarm display, press depth and speed together momentarily to display CAL. Press depth and speed together again momentarily to enter edit mode (+ and - displayed). Press and hold depth and speed together for 2 seconds, to exit edit mode and save the new value. Chapter 1: Operation 3 Silencing the shallow alarms Press speed or depth to silence the audible alarm for a period of two minutes. If, after 2 minutes, the water depth is still below the alarm setting, the alarm will be activated again. Note: When the audible alarm is silenced the alarm icon continues to flash. Turning shallow alarm ON and OFF 1. Press depth and speed together for 2 seconds to exit CAL mode. Offset This is the distance (feet or metres) from the Biducer to the bottom of the hull or to the waterline, which can be a positive (+) or negative (-) value. Default display The depth display will always default back to water depth 8 seconds after the last key press. Loss of signal If there are no depth echoes for 10 seconds, the feet/metres legend flashes and the last recorded depth is displayed until a new echo is received. 4 ST30 Round Bidata Owner's Handbook 1. 3 Speed key functions The following flow chart shows the speed key functions. bidata depth speed depth speed SPEED TRIP LOG D1764-2 Speed The speed display can be either knots (Kts), miles per hour (Mph), or kilometres per hour (Kph). Trip distance Trip is the distance covered between power on and power off. This can be nautical miles (NM), kilometres (KM), or statute miles (SM). Resetting Trip Distance Press and hold the speed key until the trip distance is zeroed - distance flashes after 1 second and during the resetting process. Ships log When this value exceeds 999 NM, SM, or KM, the Bidata displays the log as thousands (th) and, after 3 seconds, hundreds, tens, and units. For example, 1525 nm would be displayed as 1th then 525. Chapter 1: Operation 5 1. 4 LCD illumination bidata depth speed depth speed 1 second High (L3) Medium (L2) Low (L1) OFF (L0) D1765-2 The Bidata has four illumination settings, off, low (L1), medium (L2), and high (L3). The Bidata automatically returns to normal operation 5 seconds after the last key press. If the shallow depth alarm is activated the illumination display is ignored. 6 ST30 Round Bidata Owner's Handbook Chapter 2: Maintenance and Faultfinding 7 Chapter 2: Maintenance and Fault Finding 2. 1 Maintenance Servicing and safety · Raymarine equipment should be serviced only by authorised Raymarine service technicians. They will ensure that service procedures and replacement parts used will not affect performance. · Some products generate high voltages, so never handle the cables/ connectors when power is being supplied to the equipment. · When powered up, all electrical equipment produces electromagnetic fields. These can cause adjacent pieces of electrical equipment to interact with one another, with a consequent adverse effect on operation. In order to minimise these effects and enable you to get the best possible performance from your Raymarine equipment, guidelines are given in the installation instructions, to enable you to ensure minimum interaction between different items of equipment, i. e. · Always report any EMC-related problem to your nearest Raymarine dealer. The Bidata may be flush mounted by installing the instrument from behind the instrument panel. The display bezel must not be assembled to the instrument if the Bidata is to be flush mounted. EMC installation guidelines All Raymarine equipment and accessories are designed to the best industry standards for use in the leisure marine environment. Their design and manufacture conforms to the appropriate Electromagnetic Compatibility (EMC) standards, but correct installation is required to ensure that performance is not compromised. Although every effort has been taken to ensure that they will perform under all conditions, it is important to understand what factors could affect the operation of the product. [. . . ] The extended calibration features illustrated below are cycled using the depth key. bidata depth speed depth speed 15 sec CAL d Momentary s CALIBRATION d BOAT SHOW d DEPTH DAMPING d SPEED DAMPING D5042-1 Chapter 4: Calibration 21 Calibration This screen controls access to basic calibration, to protect the settings from accidentally being changed. Use the speed key (toggle action) to select the required setting: CAL ON (1) or CAL OFF (0). Boat show This is a simulation program for dealer use only: 1 = ON and 0 = OFF. Depth and speed damping Damping controls the rate at which the displayed data is updated. The selectable range, adjusted using the speed key, is between 1 and 15, with 1 providing a rapid update and 15 a slow but smooth display update. Saving extended calibration Press and hold depth and speed together for 2 seconds. Exit extended calibration without saving Press depth and speed together momentarily. 22 ST30 Round Bidata Owner's Handbook Chapter 6: Specification 23 Specification Voltage range: Size: Depth range: Speed range: Trip: Log: Shallow alarm: Depth offset: Illumination: Operating modes: Transducer type: 10 V to 16. 5 V maximum (12 V nominal) 94. 15 mm x 54. 5 mm 0 to 120 metres 0 to 400 feet 0 to 99. 9 knots, mph, or kph 0 to 999 nm, sm, or km 0 to 5999 nm, sm, or km 3 to 33 feet 1 to 10 metres -9. 9 to + 9. 9 feet -4. 0 to + 4. 0 metres 3 levels via SeaTalk Single level via 12 V switch Master or repeater Transom mount Biducer 24 ST30 Round Bidata Owner's Handbook ST30 Round Bidata Template Cut out shaded area only Cut hole to 86 mm (33/8 in) diameter (max. ) Limited Warranty Certificate Raymarine warrants each new Light Marine/Dealer Distributor Product to be of good materials and workmanship, and will repair or exchange any parts proven to be defective in material and workmanship under normal use for a period of 2 years/24 months from date of sale to end user, except as provided below. Defects will be corrected by Raymarine or an authorized Raymarine dealer. [. . . ]