User manual RAYMARINE RAYCHART 320

[. . . ] Distributed by Any reference to Raytheon or RTN in this manual should be interpreted as Raymarine. The names Raytheon and RTN are owned by the Raytheon Company. Raychart 320 Chartplotter Owner's Handbook Document Number: 81167_3 Date: 21st November 2001 Prelim Pages iii Raychart 320 Chartplotter Owner's Handbook SAFETY NOTICES WARNING: NAVIGATION AID This device is intended to be used as an aid to navigation. Its accuracy can be affected by many factors, including equipment failure or defects, environmental conditions and incorrect handling or use. It is the user's responsibility to exercise common prudence and navigational judgement. [. . . ] If the route has been saved, the waypoint remains on the screen, but is no longer in the route. Reversing the Route This option enables a return route to be generated from an existing route which is then followed in reverse order, with waypoints renumbered accordingly. To reverse the current route either: · Press the ROUTE soft key followed by MORE. Press CLEAR to return to the default soft key display. or. . . Chapter 3: Operation 3-37 · Move the cursor over a route leg until the letters RTE appear; the route soft keys are displayed. Press the REVERSE ROUTE soft key; the current route is reversed on the screen and the waypoints are renumbered accordingly. Press CLEAR to return to the default soft key display. 3. 6 Following Routes and Going to Waypoints The default GOTO soft key accesses the functions to follow a route and Goto a waypoint or cursor. When a target destination is selected, the Chartplotter calculates bearing, distance and cross track error (XTE). This information can be shown on screen and is sent on SeaTalk and NMEA for use by an Autopilot or display on a compatible SeaTalk or NMEA repeater. You can also restart the XTE from the vessel's position and set XTE to zero at that point. When the Chartplotter is following a route, the target destination is indicated by a square around the waypoint and a dotted line shows the intended track, from your start point or previous waypoint, to the target waypoint. This section describes the following: · · · · · Go to an individual target point (an existing waypoint or the cursor). Joining a route at a selected waypoint, advancing to waypoints or restarting XTE. Target Point Arrival An alarm is triggered when approaching a waypoint. The Chartplotter can also display the vessel's actual track which can be recorded for later display. The Track function is described in Section 3. 9, Using Tracks. To access the Goto/Follow soft keys, press the GOTO default soft key; the GOTO soft keys are displayed as shown in Figure 3-42. GOTO WAYPOINT GOTO CURSOR FOLLOW ROUTE D4917_1 Figure 3-42: GoTo Soft Keys Note: The soft keys differ if a follow or goto is already in progress. 3-38 Raychart 320 Chartplotter Going To an Individual Target Point Rather than following a route, you can go directly to a selected target point. This can be an existing waypoint (not in the current route) or the cursor position. To navigate directly to an existing waypoint: 1. Select the waypoint from the Waypoint List as described in Section 3. 4. Using the trackpad, position the cursor over the required waypoint until the letters WPT and the waypoint soft keys are displayed as shown in Figure 3-27 2. To return to the default soft key display, move the cursor away from the waypoint or press CLEAR. To navigate directly to the cursor position: 1. If navigation is currently in progress you are warned ALREADY FOLLOWING ROUTE. To continue with the GOTO CURSOR operation (and stop the current GOTO ROUTE), press YES. A temporary waypoint is placed as the target and navigation starts towards it. The waypoint is shown as a square with a circle and dot at its centre and is connected to the vessel's starting position with a dashed line. When the GOTO is complete or is stopped, the temporary waypoint remains on the chartplotter screen until either another Goto or Follow is started or it is removed. [. . . ] Any waiver by either party of any default or breach hereunder shall not constitute a waiver of any provision of this Agreement or of any subsequent default or breach of the same or a different kind. Installation Templates T-1 36mm (1. 4in) 18mm (0. 7in) 19mm (0. 75") dia. for NMEA plug 36mm (1. 4in) 18mm (0. 7in) 6mm (0. 25") dia. 2 positions D4194-1 GPS Antenna Mounting Template Note: Access to the underside of the mounting surface must be available to allow for secure fixing. T-2 Raychart 320 Chartplotter T-3 Drill 4 mm hole (four positions) 5. 5 in (139. 6 mm) TOP Cut out shaded area only Note: Drill 4 mm fixing holes (four postions) before cutting out shaded area. 300/320 Template 4. 03 in (102. 3 mm) 7. 67 in (194. 94 mm) Installation Templates Raychart 320 Chartplotter Mounting Template Outer profile of instrument D4968-1 4. 33 in (109. 9 mm) 3. 8 in (96. 3 mm) T-4 Raychart 320 Chartplotter Limited Warranty Certificate Raymarine warrants each new Light Marine/Dealer Distributor Product to be of good materials and workmanship, and will repair or exchange any parts proven to be defective in material and workmanship under normal use for a period of 2 years/24 months from date of sale to end user, except as provided below. Defects will be corrected by Raymarine or an authorized Raymarine dealer. [. . . ]