User manual RAYMARINE E-SERIES FULL FUNCTION REMOTE KEYBOARD

[. . . ] Safety notices Planning the installation Integrating the Remote Station Kit Installation Accessories and spares Removing/refitting Maintenance Important information Technical support and contact details 1 Page 1 2 3 3 4 6 7 9 10 10 11 12 D7679-1 The controls WPTS MOB To manage waypoints and initiate MOB. Power To turn display off and access backlight functions and scanner controls. Trackpad To control on-screen cursor and scroll through menu items. Soft keys Press to select corresponding function identified by on-screen label. PAGE ACTIVE WPTS MOB 1 2 ABC 3 DEF DATA MENU 4 GHI 5 JKL 6 MNO 7 PQRS 8 TUV 9 WXYZ OUT OK CANCEL E RANG . 0 IN ACTIVE To select the active window. MENU To access set up menus and help information. Keypad For making alphanumeric entries in on-screen dialog boxes. Range To change the display scale. CANCEL To cancel selected on-screen option when editing data and to return to previous soft key set or menu. [. . . ] If mounting the keyboard outdoors or in an unprotected area the drain tube will need to run to a suitable exit point below the level of the keyboard. What configuration should I use? How you connect the keyboard depends on the distances between your E-Series Display, the keyboard and power source and whether or not you are connecting the keyboard to an existing SeaTalk2 system. Select the appropriate configuration from the following: Configuration 1 Cable length between E-Series Display and keyboard less than 4. 5m and Not linking into an existing SeaTalk2 system. Supplied in the box Not supplied/accessory/ existing system E Series display E-Series Display SeaTalk2 Keyboard Keyboard cable (attached/3 m) SeaTalk2 cable (1. 5 m) SeaTalk2 Power/RF ground cable (1. 5 m) 5A circuit breaker Or: Switch with 5A fuse red black grey Terminator Junction box Terminator 12v supply D7680-1 4 Configuration 2 Cable length between E-Series Display and keyboard exceeds 4. 5m and Not linking into an existing SeaTalk2 system. Supplied in the box SeaTalk2 Keyboard Not supplied/accessory/ existing system E Series display E-Series Display Keyboard cable (attached/3m) SeaTalk2 extension cable (see 'Accessories') SeaTalk2 cable (1. 5m) SeaTalk2 Power/RF ground cable (1. 5m) 5A circuit breaker Or: Switch with 5A fuse red Junction box 12v supply black Terminator Terminator Additional junction box grey Configuration 3 Integrating the keyboard into an existing SeaTalk2 system. Supplied in the box Not supplied/accessory/ existing system E Series display SeaTalk2 Keyboard E-Series Display Keyboard cable (attached/3m) SeaTalk2 cable (1. 5m) SeaTalk2 extension cable (see 'Accessories') SeaTalk2 extension cable (see 'Accessories') To: Existing SeaTalk2 system (incorporating terminators, power/RF ground) Junction box To: Existing SeaTalk2 system (incorporating terminators, power/RF ground) D7697-1 5 Integrating the Remote Station Kit Station 1 Other SeaTalk devices connected Alarm No other SeaTalk devices connected Alarm M1500 monitor Brown Black SeaTalk2 Keyboard OR Other SeaTalk devices Drain Yellow OR Refer to 'Planning the Installation', diagrams on pages 4 and 5. Junction box Remote Station Kit SeaTalk/Alarm out cable, 1. 5m Station 2 E Series SeaTalk2 cable (1. 5 m) Keyboard cable (attached/3 m) Not supplied/accessory/existing system D7703-1 6 VGA out cable, waterproof (see Accessories) Drain White Black Red 12v supply Red VGA out cable, 5m NOT waterproof Brown Yellow Black Red White Black Red Installation Note: Before installing the keyboard, please read 'Planning the installation' on Pages 4 & 5. What tools do I need to install the keyboard? Drill 10 mm (3/8 in) drill bit File Jigsaw Masking or adhesive tape How do I install the keyboard? 1. Using self-adhesive or masking tape, fix the template in the required position. Note: Ensure that there are no cables or other parts that will be damaged, when the panel is drilled and sawn. 3. Remove the tape and the template remains. Smooth the sawn edges with a file. 7 D7699-1 Installation - continued 5. Peel the backing from the gasket and stick it to the underside of the cradle. 8. Fit the keyboard assembly into its housing. With the dimples in the clamps fitting into the nipples on the cradle, fit and secure the clamps in place using the thumb nuts. 6. Ensuring that the power is connected last, connect all the cables, terminators etc in the appropriate configuration (see 'Planning the Installation' on pages 4 to 6). If mounting the keyboard in an area unprotected from rain and/or sea spray, fit the drain tube and ensure that it runs to a suitable exit point below the level of the keyboard and the studs. 8 D7700-1 Accessories and spares What accessories are available?Description SeaTalk2 power/RF ground cable (1. 5m) Auxiliary alarm M1500 monitor kit (includes 5m VGA Out cable) Terminator Junction box SeaTalk2 extension cables: E25040 E25042 E25043 E25038 E25044 cable (1. 5m) E55053 E55055 E55056 E05012 1 metre 3 metres 5 metres 10 metres 20 metres E-Series SeaTalk2 VGA Out cables (waterproof): 10 metres 20 metres Trunnion mount kit Part no. E55070 E26033 E02009 E25048 E25049 What spares are available?Description Cradle assembly (includes cradle, cable, drain tube, gasket and latch) Flush mount kit (includes gasket, clamps, drain tube, studs and thumb nuts) Latch Suncover Part no. R58213 R58211 R89043 R58212 9 D7698-1 Removing/refitting How do I remove the keyboard?raise it from the cradle and lift the it from the cradle. How do I refit the keyboard?Position the top edge of the keyboard under the lip of the cradle. 2. Push the bottom of the keyboard into the cradle to engage the latch. Maintenance What routine checks and servicing can I do?. . . On a regular basis, examine all cables for signs of damage, such as chafing, cuts or nicks and check that all cables are securely connected. [. . . ] Whilst the WEEE Directive does not apply to some of Raymarine's products we support its policy and ask you to be aware of how to dispose of this product. The crossed out wheelie bin, illustrated above, and found on our product signifies that this product should not be disposed of in general waste or landfill. Please contact your local dealer, national distributor or Raymarine Technical Services for information on product disposal. 11 D7707-1 Technical support & contact information www. raymarine. com Visit the Customer Support area of our website for Frequently Asked Questions, servicing information, e-mail access to the Raymarine Technical Support Department and details of Raymarine agents, worldwide. United States For accessories and parts contact: Your authorized Raymarine dealer. [. . . ]