User manual RAVENHEAT RSF 84E

[. . . ] ELECTRONIC IGNITION - AUTOMATIC MODULATING BOILER FANNED COMBI RSF 84E - RSF IOOE RSF 84ET - RSF IOOET WITHOUTTIMER o RSF 84E G. C. No 47 581 25A NATURAL GAS (G 20) AND PROPANE (G 31) Tested, certified and service listed Listed by The United Kingdom Water Fitting Byelaws Scheme WITH TIMER RSF 84ET G. C. No 47 581 26A NATURAL GAS (G 20) AND PROPANE (G 31) INSTALLATION AND SERVICING INSTRUCTIONS TO BE LEFT WITH USER Technical and illustrative data are not binding and can be modified without prior notice. The descriptions and illustrations in the present booklet are for guideline purposes only. RAVENHEAT MANUFACTURING LTD. , CHARTISTS WAY, MORLEY, LEEDS, LS27 9ET. [. . . ] IMPORTANT: in line flue bend - 750 mm must be deducted from overall length for each 90o bend. Obtuse flue bend - 375 mm must be deducted from overall length for each 135" bend (Fig. 37 - Screw in the two upper coach bolts leaving them about 10 mm out from the wall in order to enable the boiler to be located. 30). 5. 7. 5 5. 6 5. 6. 1 COMPLETING BOILER INSTALLATION Reassembles the outer casing (sect 5. 4) proceeding in this order 1) Fit the two sides. 39) -Attach the template to the wall with adhesive tape, making sure that the centre line is vertical and that the distance from the centre line to the nearest side wall is not less than MEASUREMENT IN TABLE 6. -Mark the four boiler securing holes on the wall and extend the axis of the flue duct hole to the side wall ensuring it is horizontal. 28), measure the distance y between the centre of flue duct hole to the corner. hole in the side wall for inserting the flue duct. 5. 7 5. 7. 1 - If the standard duct furnished with the boiler is too long (position of the boiler from the wall to go through as illustrated in the drawing and wall thicknesses less than what was specified above) it can be shortened as follows: Fig. - Remove the centering spring 65, pull the flue terminal disengage inner flue duct. - Cut the outer air duct (100 mm dia. ) at right angles and to a length equal to W+Y - 47 mm. - Cut the inner flue duct (60 mm dia. ) at right angles and to a length equal to W+Y + 65 mtn. 39B 56 I 128 I 63 IN LINE FLUE BEND AND FLUE EXTENSION I 59 I KEY 56 - Sample point (if required) 57 - Elbow Header 59 - Rubber seal 0 60 63 64 65 128 Air intake duct extension - Flue Exhaust duct extension - Pipe centering spring - In Line Bend (45" and/or 90") 23 5. 7. 6 Insert the flue assembly into the wall, making sure it will not interfere when fixing the boiler on the wall. Working above the boiler pull the flue duct towards the elbow in order to engage tube into its header (Fig. Position flue into straight header and push so as to locate inner and outer flue correctly. Extension kits are available on order for flue extension of up to 2. 5 metres total length (Fig. For further details see sect 5. 5. 10. 5. 7. 12. 1 VERTICAL FLUE OPTIONS The vertical flue kit is intended for use where a horizontal flue outlet is not possible or desired. The vertical flue can be used either with a flat roof or a pitched roof (maximum pitch 60"). Where a straight vertical flue is not possible or desired, an offset vertical flue can be used in conjunction with a side horizontal flue extension piece and an inline 135190" flue bend (Fig. 41). 5. 7. 7 5. 7. 6 5. 7. 10 5. 7. 11 5. 7. 12 VERTICAL FLUE INSTRUCTION ONLY INLINE FLUE BEND - 750 MM MUST BE DEDUCTED FROM OVERALL LENGTH FOR EACH 90" BEND OBTUSE FLUE BEND - 375 MM MUST BE DEDUCTED FROM OVERALL LENGTH FOR EACH 135" BEND Fig. 41 24 Important: Make sure that the flue header dia 60 mm duct is inserted fully onto the fan spigot. POSITION MIN. DISTANCE mm N above roof level (to base of terminal) 300 300 P from adjacent wall to flue Q from internal comer to flue 300 S from facing terminal 1, 200 M horizontally from a vertical terminal to a wall 300 Before proceeding with installation check the contents of the RAVENHEAT VERTICAL FLUE KIT, comprising of the following pieces: - 1 RAVENHEAT VERTICAL FLUE complete with terminal assembly (for vertical flue application). -Additional 1000 mm (approx) Flue Extension pieces as necessary, each extension is provided with flue centering bracket. [. . . ] Before fitting the twin flue header locate the 60 mm `0' ring into the header outlet. Apply silicone lubricant and carefully push in from the bottom the 60 mm alluminium tube item 2 fig. Locate the ceiling washer fixing the twin flue header as illustrated making sure that the inner aluminium exhaust locates firmly on the fan outlet spigot. Make sure that the screws are satisfactorily located through the gasket seal. [. . . ]