User manual RANE MP 22Z

[. . . ] Never connect anything except a Rane RS 1 to the thing that looks like a red telephone jack on the rear of the MP 22z. This is an AC supply and requires some special attention if you do not have an operational power supply exactly like the one that came with your unit. Consult the Rane factory for a replacement or substitution. WEAR PART This product contains the following wear part subject to the ninety (90) day warranty period described on page Warranty-1: (1) Active Crossfader Assembly F 60. Figure 1. Crossfader Contour control Manual-1 FRONT PANEL DESCRIPTION MAIN MIC A TREBLE 2 4 EQ ENGAGE CUT BOOST 2 4 INPUT SELECT LINE 3 PH/LN1 LINE 4 LINE 5 INPUT SELECT LINE 4 PH/LN2 LINE 5 LINE 6 B TREBLE 2 4 EQ ENGAGE CUT BOOST 2 4 2 AUX 4 6 8 0 10 LEVEL 2 4 OUTPUT LEVELS 6 8 10 0 ZONE 1 2 10 0 ZONE 2 4 6 8 PEAK dBu +8 +5 +3 HI-MID 2 2 4 CUT 2 BOOST 4 CUT BOOST 2 2 4 CUE A CUE B HI-MID 2 2 4 CUT BOOST 10 MASTER LEVEL 10 +1 0 TREBLE 4 10 10 10 10 4 -1 -3 MIC EQ 2 4 4 CUT BOOST 8 0dB 8 0dB 8 8 -5 -7 MID EQ A 2 2 4 4 CUT BOOST 2 2 4 CUT BOOST 0 0 0 0 4 CUT 2 2 4 4 6 6 6 MID 6 EQ B 4 2 2 4 6 0dB -10 -15 BASS 4 4 CUT 2 2 4 BOOST 2 2 4 BOOST 0 4 LEFT 2 -20 RIGHT REMOTE MIC 2 4 6 8 BASS 2 4 BASS 0 CUE PGM MP 22z MIXER MIN ENGAGE OL MAX MAIN MIC 2 ACTIVE CROSSFADER TM 4 6 8 0 2 4 6 8 10 B 6 HEADPHONE CONTROL 2 2 6 CUE PGM PAN 2 0 10 LEVEL 4 6 8 STEREO CUE/PGM CROSSFADER CONTOUR F 60 PWR MIN ENGAGE MAX A MONO 10 8 6 4 2 0 CUE LEFT PGM RIGHT 1 Front panel MAIN MIC input: Use this XLR connector for connecting a balanced microphone of any impedance. [. . . ] Poway, CA 92064 Phone 858-486-8388 Fax 858-486-8398 (www. caig. com) REPLACING THE ACTIVE CROSSFADER The Crossfader may be removed without any disassembly of the MP 22z itself, and may be performed while the unit is operating with no interruption of the audio signal. F 60 and F 45 Fader Kits are available from your local retailer or the factory. The kit includes full assembly including knobs, ribbon, and face plate. Remove the two (2) outer screws attaching the crossfader assembly to the front panel. Pull the Crossfader Assembly forward and unplug the ribbon from the connector on the bottom board. Proceed with Cleaning Instructions, or install the replacement assembly by reversing the above instructions. Manual-3 REAR PANEL DESCRIPTION TRIM 1 TRIM 2 TRIM 3 TRIM 4 TRIM 5 TRIM 6 UNBALANCED 1/4" TIP (SIG) SLEEVE (GND) PHONO GROUND ACTIVE CROSSFADER TECHNOLOGY PATENT PENDING INPUTS L L MASTER LOOP L SEND (OUT) R AUX LINE IN L MP 22z OUTPUTS MIC/AUX TO TAPE OUT MIC/AUX TO ZONE 1 L ACN001. 187. 837 MADE IN U. S. A. REMOTE MIC/LINE MIC LOOP SEND RETURN L BALANCED 1/4" TIP (+) RING (­) SLEEVE (GND) MASTER RANE CORP. POWER R INPUT (OUT) (IN) LINE PHONO (RIAA) PH/LN 1 PH/LN 2 LINE PHONO (RIAA) LINE 3 R LINE 4 R L LINE 5 LINE 6 RETURN (IN) R R TAPE R YES NO YES NO ZONE 1 ZONE 2 L R 750mA CLASS 2 EQUIPMENT 1 REMOTE MIC/LINE INPUT: This ¼" tip-sleeve Input is for wireless mics or other high-impedence sources. 2 MICROPHONE LOOP jacks: These ¼" tip-sleeve connectors are for inserting external signal processing in the microphone circuit only. 3 PHONO GROUND screw: This can facilitate your hum chasing, buzz eliminating experiments, providing a place to connect those extra wires coming out of the turntables. 4 PHONO/LINE 1 & 2 INPUTS: These stereo Inputs are switchable from a PHONO (RIAA) stage for magnetic cartridges to a LINE level Input suitable for any line level device such as a CD player. Each Input may be adjusted with its TRIM control for level matching purposes if desired. 5 LINE 3, 4, 5 & 6 INPUTS: These stereo pairs of RCAs connect LINE level Inputs only. Each Input may be adjusted with its TRIM control for level matching purposes if desired. 6 MASTER LOOP SEND & RETURN: These stereo pairs of RCA connectors allow inserting external signal processing in the Master, Zone and Headphone circuits. These are switching jacks--always finish the loop when connecting send or return. Only connect to a device that is capable of returning signal back to the MP 22z. 7 AUX LINE INPUT: This stereo pair of RCA connectors is an extra set of LINE level Inputs with an independent front panel LEVEL control (see Front Panel, 7). 8 TAPE OUTPUT: These line level RCA Outputs are intended for use with a tape recorder, but not necessarily restricted to that purpose. 9 MIC & AUX TO TAPE OUT switch: In the YES position the Mic and Aux signals along with all Inputs are routed to the TAPE OUTPUT. In the NO position only program material from Inputs 1 through 6 appear at the TAPE OUTPUT. The Main Mic Input on the front panel allows use of a gooseneck mounted microphone. The connector is rotated such that a right angle connector may be used when connecting via mic cable. [. . . ] Modifying the sound of the mic in this way won't affect the EQ of the music in the system. The three Equalizer sections (Mic and Input A and B Channels) are totally independent. When the mic is not in use, release the MIC ENGAGE switch again to its up position, extinguishing the LED. Should the microphone preamp become overloaded, the red LED Overload light illuminates. [. . . ]