User manual RANE CP R2 INSTALLATION

[. . . ] INSTALLATION MANUAL CP R1 & CP R2 REMOTE CONTROLS FOR CP 62 See the CP 62 Manual for operating instructions. CP R1 Zone Assign Remote Control When installing the R1 Remote, locate it next to the paging source. The R1 connects to the REMOTE ZONE ASSIGN jack next to the paging inputs on the rear of the CP 62. Two Paging Sources with No CP R1 Remote Control When using both paging inputs but not the CP R1 remote you do need to plug in and set the configuration adapter, (the short piece of wire with the phone plug and stripped wires included with the CP 62. ) This adapter tells the CP 62 where one of the paging sources needs to go. The front panel PAGING ZONE ASSIGN switch (see Front Panel, balloon #6) routes one paging source and the configuration adapter routes the other. [. . . ] Which signal is controlled from the front panel PAGING ZONE ASSIGN switch (see Front Panel, ballon #6) and which signal is controlled by the REMOTE ZONE ASSIGN connector (Rear Panel, balloon #15, the place you plug in the CP R1 remote. ) To use the CP R1 remote to control the XLR MIC signal set the rear panel PAGING INPUTS ASSIGN switch to the MIC position. To control the PHONE/LINE signal, set the PAGING INPUTS ASSIGN switch to the PHONE/LINE position. CP R2 Source & Level Remote Control Table 1 shows the flexibility of configuring the R2. The R2 controls operate the same as the PROGRAM SELECT and ZONE LEVEL controls on the front of the CP 62, when enabled by the front panel REMOTE CONTROL button. ZONE 1 STEREO MODE Locate and set the switch in the R2 to STEREO, as shown in Figure 1a. ZONE 1 MONO MODE This delivers a total of three mono zones from the CP 62. To separate Zone 1 into 1a and 1b, use two R2 remotes connected to Zone 1. Plug a cable from the MAIN jack of the first R2 into the ZONE 1 REMOTE jack on the back of the CP 62 and set the first R2s slide switch to DUAL MONO, as shown in Figure 1b. Plug a cable from the MAIN jack of the second R2 into the AUX jack on the first R2. A third R2 plugged into the CP 62 ZONE 2 REMOTE jack gives control over the third mono zone, operated as Zone 2. Figure 1a. Figure 1b. Table 1. R2 Installation Options Desired Configuration 1 Stereo Zone (Zone 1) 1 Mono Zone (Zone 2) Both of the above 3 Mono Zones (Zones 1a, 1b, & 2) Zone 1a and 1b use the same Source Selection Remote Functions SELECT & stereo LEVEL SELECT & mono LEVEL both as above Independent mono LEVEL for Zone 1a, 1b, and 2. Zone 1 Mode STEREO not applicable STEREO MONO R2 Connections CP 62 ZONE 1 SOURCE & LEVEL jack CP 62 ZONE 2 SOURCE & LEVEL jack 2 R2 units both as above Use 3 R2s. Zone 1a - first R2's MAIN to the CP 62 ZONE 1 SOURCE & LEVEL jack. Zone 2 - third R2 to CP 62 ZONE 2 SOURCE & LEVEL jack. DECORA is a registered trademark of Leviton Manufacturing Co. , Inc. Preparing the cables All modular connectors are not created equal. The typical modular plug that connects to your telephone is a 6-position/ 4-conductor connector, named by an RJ number to describe it (i. e. The appropriate connector for the CP 62 is a 4-position/4-conductor, and is referred to as a "telephone modular handset connector". Install standard copper stranded 28-26 guage 4 conductor flat telephone cable to an empty electrical box where the remote is to be located. [. . . ] Stereo and Mono Zone Control Example ©Rane Corporation 10802 47th Ave. W. , Mukilteo WA 98275-5098 TEL (206)355-6000 FAX (206)347-7757 WEB http://www. rane. com Printed in the U. S. A. on Recycled Paper All features & specifications subject to change without notice. [. . . ]