User manual RADIOSHACK Z-707 BATTLE IRON CLAW

[. . . ] 15 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Volume Unlock on a Cable Convertor or SAT/DSS Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Resetting Volume Lock to the Original Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Device Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . © 2001 RadioShack Corporation. [. . . ] Note: Once you have programmed SCAN/FAV for Favorite Channel Scan, you cannot use it for Channel Scan unless you reset it (see "Resetting Scan"). Enter the two-, three- or four-digit number for your favorite channel. If you entered a two- or three-digit channel number, you must do one of the following: if your original remote requires you to press Enter or Select to send a command, then do so after entering the digits of your favorite channel. If your original remote does not require you to press Enter or Select to send a command, then after entering your two- or three-digit channel number, press P. If you entered a four-digit channel number, do not press P. 6. Repeat Steps 4­5 up to nine more times to store another favorite channel for the same device, or exit the program by pressing P until the red light blinks twice. Once you have programmed all 10 favorite channels, the remote automatically exits favorite channel setup. Resetting Scan Once you have programmed SCAN/FAV for Favorite Channel Scan, you cannot use it for Channel Scan unless you reset it. You can now use the remote for Channel Scan (see "Using Channel Scan" on Page 16). Hold down P until the red light blinks twice. Preparation 11 PROGRAMMING MACROS Your remote has four macro keys (MUSIC, MOVIES, SPORTS, and NEWS) that store up to three channels per macro key for instant tuning of TV or cable/satellite channels. Press the device key for the device you are adding (for example, VCR) then press the device key for the unused key where the additional device will be assigned (for example, AUX). Set up the reassigned key to control your device (see "Setting Up Your Remote" on Page 9). Preparation 13 Note: Other reassignments are possible, including adding a second TV or second DVD player to an unused device key. Simply repeat Step 3 with your desired choices. Resetting Reassigned Device Keys If you have reassigned a key (for example, you reassigned the DVD key to operate a second VCR), and want to return to the default setting (for the example, DVD mode), follow these steps. The remote tunes to each favorite channel in ascending order every three seconds. Press any key to stop the scan. USING MACROS Press the desired macro key once for the first channel you programmed (see "Programming Macros" on Page 12), twice for the second channel, and so on. USING THE POWER KEY To turn on all devices, hold down POWER for at least 2 seconds. Each device turns on in the sequence you programmed (see "Programming the Power Key" on Page 12). To turn off all devices, press TV, then hold down POWER for at least 2 seconds. Note: If you do not press TV first before holding down POWER, the sequence will skip the currently selected device. CHANGING VOLUME LOCK Your remote's Volume Lock is preset so the volume and mute keys only control the TV volume, no matter what device is selected. If you want the remote to control the TV's volume only, skip this section and leave the original settings intact. However, if you want to control another device's volume functions (for example, CBL/SAT, VCR, DVD, Operation 17 CD, or AUX) upon its selection, then perform the steps listed in the appropriate section below. Volume Unlock on a Cable Convertor or SAT/DSS Receiver 1. To control the volume through your cable converter (or SAT/DSS receiver), press CBL/SAT before using the volume controls. Volume Unlock on a VCR 1. To control the volume through your VCR, press VCR before using the volume controls. Volume Unlock on a DVD 1. To control the volume through your DVD player, press DVD before using the volume controls. Volume Unlock on a CD Player 1. To control the volume through your auxiliary device, press CD before using the volume controls. Volume Unlock on an Auxiliary Device 1. [. . . ] When the red light blinks three times, the search of every code is complete. Note: If the device turns off during the search, but does not operate after you lock in the code, begin the search again, pausing longer between key presses. Checking Your Code If you set up the remote control using the manual code search procedure, you can use the following instructions to find out what code is operating your equipment: Operation 23 1. Count the number of blinks (for example, if there are three blinks, the first digit is 3) and write down the number. Note: The red light will not blink if the code digit is a "0". [. . . ]