User manual RADIOSHACK 4-IN-1 LIGHT-UP REMOTE

[. . . ] Television Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . © 2001 RadioShack Corporation. All Rights Reserved. RadioShack and RadioShack. com are trademarks used by RadioShack Corporation. 20 20 22 22 22 23 2 Contents VCR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 ^ Features Your Radio Shack 4-in-One Light-Up Remote lets you control your TV, VCR, cable/SAT/DSS converter, and DVD player with one easy-to-use remote control. [. . . ] Note: Once you have programmed SCAN/FAV for Favorite Channel Scan, you cannot use it for Channel Scan unless you reset it (see "Resetting Scan" on Page 10). Preparation 9 1. Enter a desired two-, three-, or four-digit channel number (for example, 050 or 0500), depending on your device. If you entered a two- or three-digit channel number, you must next do one of the following: · If your original remote requires you to press Enter or Select to send a command, then do so after entering the digits of your favorite channel. · If your original remote does not require you to press Enter or Select to send a command, then after entering your two- or three-digit channel number, press P. If you entered a four-digit channel number, do not press P. 5. Repeat Step 4 up to nine more times to store another favorite channel for the same device, or exit the program by pressing P until the red light blinks twice. Note: Upon entering the tenth channel, the remote exits favorite channel programming. Programming Favorite Channel Scan for a second device deletes the programming for the first. Resetting Scan Once you have programmed SCAN/FAV for Favorite Channel Scan, you cannot use it for Channel Scan unless you reset it. You can now use the remote for Channel Scan (see "Using Channel Scan" on Page 14). Hold down P until the red light blinks twice. PROGRAMMING MACROS Your remote has four macro keys (MUSIC, MOVIE, SPORT, and NEWS) that you can use to store up to three channels per macro key for instant tuning of TV or cable/ satellite channels. For example, if your favorite sports channel on your cable service is 061, you can store it as an instant tune-in macro. Press the device key for the device you are adding (for example, VCR) then press the device key for the unused key where the additional device will be assigned (for example, DVD). Set up the reassigned key to control your device (see "Setting Up Your Remote" on Page 8). Note: Other reassignments are possible, including adding a second TV or second DVD player to an unused device key. Simply repeat Step 3 with your desired choices. Resetting Reassigned Device Keys If you have reassigned a key (for example, you reassigned the DVD key to operate a second VCR), and want to return to the default setting (for the example, DVD mode), follow these steps. Press the desired mode key (the key you want reassigned to factory default settings) twice. You can now set up codes for the original device. Preparation 13 ^ Operation Note: The command keys on the remote control work the same as the keys on your original remote controls. Point the remote at the desired device and press the device key (TV, VCR, CBL/SAT, or DVD). To turn off the last device you selected, press POWER. To turn off another device, press the device key, then press POWER. Repeat this step to turn off all devices. Note: You can program POWER as a master power key to turn all devices on and off in a sequence. See "Programming the Power Key" on Page 12. USING THE LIGHT Your remote has a backlight so you can see the keys in the dark. To turn off the light, press again. USING CHANNEL SCAN Important: If you have set up SCAN/FAV for Favorite Channel Scan, you cannot use Channel Scan until you reset SCAN/FAV (see "Resetting Scan" on Page 10). If you want to view a sample of every channel on your cable or SAT/DSS service, press CBL/SAT, then press 14 Operation SCAN/FAV. Starting with the current channel, the remote control tunes to each channel in ascending order every three seconds. [. . . ] In the event of a product defect during the warranty period, take the product and the RadioShack sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise provided by law: (a) correct the defect by product repair without charge for parts and labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase price. All replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of warranty service. [. . . ]