User manual RADIOSHACK 3-IN-1 EASY REMOTE CONTROL

[. . . ] 15-1931 OWNER'S MANUAL 3-in-One Easy Remote Control Please read before using this equipment. 15-1931. fm Page 2 Monday, July 19, 1999 2:26 PM FEATURES Your RadioShack 3-in-One Easy Remote Control can replace up to three infrared remote controls. Unlike some universal remote controls, your remote control is preprogrammed with the most commonly used commands and does not have to learn its commands from the original remote controls. All you have to do is tell it which TV, VCR, or cable converter's remote controls you want to replace (by entering 3-digit codes). This manual includes a list of many manufacturers' 3-digit codes for TVs, VCRs, and cable converters. [. . . ] Call 1-888-533-7135 8 15-1931. fm Page 9 Monday, July 19, 1999 2:26 PM to control the sound. To turn off punch-through, hold down P until the red light blinks twice, then press 9 9 3 and the device key. If you want to control the volume through your cable box, press CBL before using the volume control. If you want to control the volume through your VCR, press VCR before using the volume control. To turn punch-through back on, hold down P until the red light blinks twice, then press 9 9 3 VOL . FAVORITE CHANNEL SCAN You can use your remote control to scan through up to 10 of your favorite channels on your TV, VCR, or cable box. Note: You can scan channels only for one device (TV, VCR, or CBL) at a time. You cannot set up a favorite channel list for another device until you clear the existing list. Press the device key for the device with the channels you want to program (TV, VCR, or CBL). Enter the channel number of the first channel you want to include in your favorite channel list. Notes: · Precede a single-digit number with a 0 -- for example, 01, 02, and so on. Need help?Call 1-888-533-7135 9 15-1931. fm Page 10 Monday, July 19, 1999 2:26 PM · If you enter a three-digit number, you do not need to press P after entering the number. Repeat Step 3 for other channels (up to 10) you want to include in your list. To scan through the favorite channel list, press the device key for the device you want to tune (TV, VCR, or CBL), then press SCAN. The remote control repeatedly scans through the favorite channel list, stopping on each channel for about 3 seconds. Press any key other than SCAN when you see a channel you want to watch. Scanning stops. Clearing Favorite Channel Scan You must clear the channels in your favorite channel scan list if you want to change them. Press 9 9 6, then hold down P until the red light blinks twice. Need help?Call 1-888-533-7135 10 15-1931. fm Page 11 Monday, July 19, 1999 2:26 PM IF YOU HAVE PROBLEMS MANUAL CODE SEARCH If the 3-in-One Easy Remote Control does not operate your remote-controlled devices when you first set it up, you might have to manually find the correct code for your devices. You can try all the codes listed in "Manufacturers' Codes" on Page 13 for the brand of your device, or you can follow these steps to search the remote control's entire library. Repeatedly press PWR then the device key for the device until it responds to the command. When the device responds to the command, press P within 5 seconds to save the code. Note: If you do not press P within 5 seconds, the remote control does not save the code. [. . . ] Call 1-888-533-7135 26 15-1931. fm Page 27 Monday, July 19, 1999 2:26 PM CARE AND MAINTENANCE Your RadioShack 3-in-One Easy Remote Control is an example of superior design and craftsmanship. The following suggestions will help you care for your remote control so you can enjoy it for years. Liquids might contain minerals that can corrode the electronic circuits. Handle the remote control gently and carefully. Dropping it can damage circuit boards and cases and can cause the remote control to work improperly. Use and store the remote control only in normal temperature environments. [. . . ]