User manual QUANTUM SUPERLOADER 3 V61 FIRMWARE RELEASE NOTES 02-2009

[. . . ] 2 Resolved Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Known Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] However, until the user power cycles, active operations from the OCP are not allowed. Code Update 0 PCR4564 -- Firmware update fails with Firefox on Windows Vista 0 When performing a firmware update of the autoloader system code over the RMU, do not use the combination of the Firefox browser on the Windows Vista® operating system. The update can fail, but will not adversely affect the operation of the system. Tech Bulletin 6-01828-07 "SuperLoader 3 Firmware Update Fails with Firefox on Windows Vista" has been issued. The IE7 browser on Vista works without problem, and Firefox on Win 2003 works without problem. PCR17898 -- OCP gives no indication that drive FW is being updated 0 While updating drive code over SCSI, the OCP shows "Updating Drive" if the OCP is at the top menu. Hitting the ESC key to return to the top level shows the "Updating Drive" message. While drive code is being updated, moves involving the drive are not allowed. PCR17770 -- DFU utility doesn't FUP from v53 to T60 SL3 for LTO3 or LTO4 On systems with Quantum LTO3 SCSI drives (v2023) and LTO3 HH SAS drives (v2076), when performing an autoloader code update over the primary interface using the DFU application versions 1. 3. 9 or 1. 3. 10, the code update will fail. To perform the update, use the RMU interface. 0 Remote Management Unit (RMU) 0 PCR17957 -- Client Authorization Control - No error message for invalid characters and bogus address is saved 0 On the RMU page, Configurations->Security, under the heading "Client Authorization Control, " be sure that any IP address values that are entered contain valid characters. If not, the invalid characters will simply be ignored, and the remaining valid characters will be taken as the IP address. PCR17976 -- RMU Client Authorization Control Reset button does not gray out/ Enable IPV4/IPV6 address fields properly 0 On the RMU page, Configurations->Security, under the heading "Client Authorization Control, " if the user chooses to reset the IP address fields, the user must press the "Reset" 4 Known Issues Release Notes Document 5502229 Rev C February 2009 button twice in order to see proper gray-out behavior of any fields under a disabled control address range. PCR18052 -- After enabling TLR from RMU library DHCP address set to 0. 0. 0. 0 On the RMU's Configuration page of LTO3 HH SAS and LTO4 HH SAS systems, when the user enables or disables the SAS Transport Layer Retries (TLR), the user is requested to power cycle the system. After power cycling, the user may be unable to connect a browser to the system if it is configured to use DHCP address assignment. If this is the case, one can use the OCP's Status->Ethernet screen to check the IP address; it may be 0. 0. 0. 0. PCR18216 -- Setting static site local address to current router assigned mishandled0 With an existing static site local IPv6 address set, when setting the IPv6 address to a new site local address that is the same as the current router-assigned site local address, the new address is rejected without giving the user an error message that the address was rejected. Also, when the new address is rejected, the prior old static site local address is removed from the "Current Network Parameters" section on the Configuration page and is no longer functional. To restore this site local connectivity, either clear the IPv6 address from the RMU field and submit or enter a non-router-assigned address value. PCR18376 -- Unable to connect using IPv6 site and global address RH5. 1 0 0 When using Red Hat 5. 1, Firefox 1. 5. 0. 12, or other browsers, you may not be able to connect to the SuperLoader 3 system. [. . . ] The user is presented with a login screen, and the login attempt will fail. To workaround this, cancel the login window, and select a page that does have operator access, such as the Command page. When connecting Internet Explorer to a system, a Log-In pop up window may appear. [. . . ]