User manual QUANTUM SNC 5100 FOR THE SCALAR 1000 AND 10K

[. . . ] SNCTM 5100 for the Scalar ® 1000 and 10K User Guide Copyright Notice © Copyright ADIC 2002 The information contained in this document is subject to change without notice. This document contains proprietary information which is protected by copyright. No part of this document may be photocopied, reproduced, or translated to another language without prior written consent of ADIC. ADIC shall not be liable for errors contained herein or for incidental or consequential damages (including lost profits) in connection with the furnishing, performance or use of this material whether based on warranty, contract, or other legal theory. [. . . ] If the test passes, remove the loop back cable and go to "Ethernet Test". If the test does not pass, go to "Start MAP" on page 42. Ethernet Test For further information about the procedures and commands used in this section, see "Connecting to the Service Port" on page 95 and "Diagnostic Command Reference" on page 187. 86 Final Diagnostic Tests 6-00020-02 SNC 5100 Step 1. Configure the Ethernet Port Host Name, Address, Routes, Enable Ethernet. For more information, see "Network Setup for the SNC 5100". Step 3. For more information, see the "elTest" command on page 192. Step 5. If the test passes, go to Step 6. If the test does not pass, go to See "Start MAP" on page 42. Step 6. Proceed to "Updating the SNC 5100". Network Setup for the SNC 5100 The SNC 5100 must be connected to a 10/100-base-T Ethernet network for use with the ADIC Management Console software. An RJ-45 connector is located on the rear panel of the SNC 5100 for connection to the Ethernet. You will need to connect a terminal or terminal emulator to the Service Port of the SNC 5100 in order to configure the IP address. 6-00020-02 Network Setup for the SNC 5100 87 SNC 5100 Figure 8 Step 1. Ethernet Port To configure the network, connect to the SNC 5100 Service Port. For more information, see "Connecting to the Service Port" on page 95. In all of the subsequent steps, substitute the values you determined in Step 6 of Table 2, "Pre-Installation Checklist, " on page 19. Step 2. Enter the hostNameSet command to set the Host name. For more information, see the "hostNameSet" command on page 138. In the example shown, the host name of the SNC 5100 was "SN60023" and is now being set to "foster. " The shell prompt will change to reflect the new name. Example: SN60023 > hostNameSet "foster" Target hostname set to foster value = 0 = 0x0 foster > Step 3. Use the ethAddrSet command to set the host network address: For more information, see the "ethAddrSet" command on page 121. The IP address is specified as four decimal numbers, separated by periods. Example: foster > ethAddrSet "192. 168. 1. 54" Host Address set to 192. 168. 1. 54 for Ethernet interface value = 0 = 0x0 88 Network Setup for the SNC 5100 6-00020-02 SNC 5100 If you need to set a netmask, specify it after the network address: Example: foster > ethAddrSet "10. 0. 0. 2", "255. 0. 0. 0" If you need a network route and/or default gateway, you must specify it. Example: foster > gateAddrSet "192. 168. 1. 1" value = 0 = 0x0 When more complicated routing is required, use the route command to specify the destination address, as a full address (single host) or as an abbreviated subnet address. Specify the address of the gateway that is reachable on the local subnet. Example: foster > route "add", "206. 0. 0", "192. 168. 1. 1" value = 0 = 0x0 Step 4. Optionally, add User account for Telnet If you want to access the SNC 5100's command line interface through its Ethernet port using a Telnet session, you need to add a user account. For more information, see the commands beginning with user in the "Service Port Command Reference" on page 105. Example: foster > userAdd "username", "password" value = 0 = 0x0 foster > Step 5. Enter the reboot command to reboot the SNC 5100: For more information, see the "ethAddrSet" command on page 121. Example: foster > reboot 6-00020-02 Network Setup for the SNC 5100 89 SNC 5100 Updating the SNC 5100 Step 1. For more information, see the "normalBoot" command on page 191. For more information, see the "version" command on page 185. Determine whether the SNC 5100's firmware version requires an update. If an update is required, download the new file or files and the associated readme. You will install the new firmware as you complete the "Post-Repair Checklist". If you replaced the SNC 5100, enter the ridTag command and type the identifier. Caution You must perform this step if you replaced the SNC 5100. [. . . ] ADIC does not warrant that the Software is compatible with the current releases of all operating systems, nor that the Software will be made compatible with new releases of operating systems within a specified amount of time, or at all. At Licensee's request, ADIC will notify Licensee of the version level of the operating system with which the Software is intended to be compatible. EXCEPT FOR THE EXPRESS LIMITED WARRANTY STATED ABOVE, ADIC MAKES NO WARRANTIES, EXPRESS OR IMPLIED, FOR THE SOFTWARE, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. This License commences on the Effective Date and will continue in perpetuity unless Licensee fails to comply with any conditions of this License. [. . . ]