User manual QUANTUM SCALAR I2000 I6.6 RELEASE NOTES 09-2009

[. . . ] Release Notes Product Operating Systems (Remote LMC Client) Date Scalar i2000® 595A. GS01601 MicrosoftTM Windows®, AIX®, HP-UXTM, SolarisTM, and Red Hat® Linux September 2009 Contents 0 Purpose of This Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 New Features and Enhancements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Compatibility and Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Resolved Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Problem when either label is misread and we get more than one label mapped to a slot, or when position of label is incorrect and mapped to an adjacent (and full) slot. 20856 20858 923844 964268 Cartridge Outside Boundaries. Only log E_CELL_CARTRIDGE_OUTSIDE_SLOT_WINDOW and E_MAGAZINE_CART_OUTSIDE_BOUNDARIES since a single slot scan has been implemented (20856) that resolves what is in a slot. Drive Comm Warning - change E_DDC_DP_DRIVE_COMMS_WARNING and E_DDC_DP_DRIVE_COMMS_FAILED events to 'informational only' so that they don't cause tickets. The RCU should not try to open a file, for writing, on the MCB more than one time. Add a check to make sure the number of entries read from the file makes sense before using the file. Removed "Statusmonitor not alive" ticket. 20870 20904 20921 20923 20924 864458 903678 914416 955072 930828 959496 898460 898460 MCB Comm Problem with RCU SOIP. 20931 20932 20997 21007 21035 21052 21069 SNMP thread issue does not allow the AMC/LMC to become ready after power cycle/ reboot. Problems in Status Monitor caused FCBs to start up and auto level slowly. Tune the I/E DLT get pattern to be more reliable and provide support for an optional DLT cleaning station. An analysis of the SDLT600 and 320 drive get operation found that the get position should be lowered by 1. 5mm and the put position lowered by 1. 0mm. Duplicate entries in fibre channel controller node name list- Capture Side. 21557 21696 21737 22540 22633 902482 902482 902482 Fixed block data transfer > 2M not rejected properly >2M transfer allowed with fixed block mode write/read. Snapshot (Extended) is not Complete. 8 Resolved Issues Release Notes Document 6-00424-44 Rev B September 2009 Known Issues This release of Scalar i2000 firmware has the following known issues. This list contains cumulative information for all previously released Scalar i2000 library versions. 0 Change Request Number 24444 Service Request Number Description SNMP v3 is not functioning due to "unknown user" issue. Workaround Change the SNMP password to a temporary password, and then change the temporary password to back to the desired password. Make sure the robot is in frame six or less before pushing the Robotics Enabled button. 22726 On a seven frame or larger library, after closing the door and enabling the robotics, the robot performs normal going ready operations like homing, scanning any closed IE stations, etc. but the library never goes online and ready after the robot stops moving. LTO-4 drive not presented to host, issue with loop id. 21695 Two workarounds available: **Set the drive to use Soft Loop ID. **Set the blades port for this target channel to Hard ID 0 to match that of the drive. However, it will be necessary to telnet to the blade and enter the 'fcRestart' for this channel for the ID change to take effect. Verify that the Java Runtime Engine (JRE) on the remote computer is up-todate. Reboot the 7400. 21608 Firmware upgrade succeeds, but GUI progress screen shows FCB upgrade failed and Help > About shows old Product Version information. AMC Web GUI locks up. 21566 18357 18354 770026 7404 Sends REC to host multiple times when host PRLI does not show REC supported. I/O blade does not support exchange recovery if host does not flag "Confirmed Completion Allowed" in PRLI. During upgrade, a Sev 1 RAS ticket is produced: The pivot assembly of the picker robotics (Scanner of the picker robotics) operation has Failed. 20409 Disregard and close the RAS ticket. Known Issues 9 Release Notes September 2009 Change Request Number 71752 71101 Service Request Number Description RES binary data compare fails with allocation length >2MB. Workaround Do not use allocation lengths >2MB. [. . . ] When service login is disabled, you are unable to login via service port when multiple IP addresses are available to the client. Make certain there is only one valid IP available on the client (disable wireless connections). Retry the update, and if the update still fails, try updating using the manual method. Due to lack of data and inability to reproduce the problem, no applicable workaround is available. 62736 62692 62417 57762 57687 57578 48014 432530 Disable service port login, except for service port access. 42342 FUP update through the GUI failed, but the FUP update was successful manually. [. . . ]