User manual QUANTUM PX502 REPACKING INSTRUCTION 81-81453-02 A01

[. . . ] Quantum PX502 Chassis Repacking Instructions Introduction Removing the Library from the Rack Installing the Internal Shipping Restraints Packing the Library for Shipment 3 3 6 12 Document 81-81453-02 A01, January 2006 1 Quantum PX502 Chassis Repacking Instructions Document 81-81453-02 A01 January 2006 Made in the USA. Quantum Corporation provides this publication "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. [. . . ] If you do not have the library packing materials, contact Quantum customer support for replacement packaging (800) 284-5101. 0 Caution: This procedure consists of the following steps: · · · Removing the Library from the Rack Installing the Internal Shipping Restraints Packing the Library for Shipment Removing the Library from the Rack To remove the PX502 library from the rack: Note: You must remove all tape cartridges from the library prior to parking the library robotics for shipment. 0 1 Using the OCP, open the front doors, remove both tape cartridge magazines, and remove any tape cartridges from the fixed bins or FlexLinkTM (refer to the Quantum PX500 Series User's Guide PN 81-81290 for information on OCP operation and bin locations). After removing the tape cartridge magazines and closing the doors, the library inventories all possible tape cartridge locations (magazines, fixed slots, Flexlink, and tape drives). 2 From the Library Operations screen on the OCP, select Park for Shipping. Note: If there are tape cartridges in the library, the system will NOT park the library robotics. You must remove all tape cartridges from the system prior to parking the library robotics. Introduction 3 Quantum PX502 Chassis Repacking Instructions Document 81-81453-02 A01 January 2006 3 From the back of the library, disconnect all power, Ethernet, and SCSI cables from the library and note their locations for later reinstallation. Disconnect all power supply cords before servicing to avoid electric shock. 4 To remove the library chassis from the rack (see figure 1): Note: Refer to the PX502 Quick Start Guide (PN 81-81292) for additional PX502 rack mount information. a b c Loosen the captive screws securing the tape drives to the chassis and remove the tape drive(s) from the back of the library. Loosen the captive screw securing the power supplies to the chassis and remove the power supplies from the back of the library. Remove PHILLIPS® screws securing each side of the chassis to the rack mounting rails and remove two Allen screws securing both clamps on the back of the library. At least two people are required to move the library chassis. d Warning: 4 Removing the Library from the Rack Quantum PX502 Chassis Repacking Instructions Document 81-81453-02 A01 January 2006 Figure 1 Removing the PX502 Library Tape drives Power supplies Right magazine Removing the Library from the Rack 5 Quantum PX502 Chassis Repacking Instructions Document 81-81453-02 A01 January 2006 Installing the Internal Shipping Restraints To ensure that the internal robotics within the library is not damaged, you must install the internal shipping restraints on the robotics. Caution: Failure to install the shipping restraints on the robotics may void your warranty. 0 To install the internal shipping restraints: 1 Place the library on a flat surface and remove the twelve PHILLIPS screws securing the FlexLinkTM cover and top cover plate to the library chassis (see figure 2): Note: If the bottom FlexLink cover has been removed, replace it before shipping the library back to Quantum. Figure 2 Removing the Top Cover Top cover FlexLink cover 6 Installing the Internal Shipping Restraints Quantum PX502 Chassis Repacking Instructions Document 81-81453-02 A01 January 2006 2 If the library is not operational and the Park for Shipping command was not executed, grasp the robotics and gently move it to the front of the library (see figure 3). Caution: Take standard ESD precautions when working within the library chassis. Note: If there are any cartridges in the fixed bins, you can remove them now. Figure 3 Moving the Robotics Back Library robotics Front 3 Install the metal restraints through the chassis eyelets as shown in figure 4. Installing the Internal Shipping Restraints 7 Quantum PX502 Chassis Repacking Instructions Document 81-81453-02 A01 January 2006 Figure 4 Installing the Metal Restraints Metal restraints Eyelet 4 Install the two halves of the robotics shipping foams as shown in figure 5: a b Install the left-hand foam first so that it fits down into the robotics platform, then push towards the back of the unit until it stops. Install the right-hand foam onto the library robotics so the motor fits into the foam opening, then push towards the front of the library until it stops. 8 Installing the Internal Shipping Restraints Quantum PX502 Chassis Repacking Instructions Document 81-81453-02 A01 January 2006 Figure 5 Installing the Robotics Restraints Left-hand shipping foam Robotics assembly shown outside of library for clarity. Robotics motor Foam inside robotics platform Right-hand shipping foam 5 Slide the robotics with the shipping foams under the metal restraints so the metal bands fall into the restraint cutouts. [. . . ] Warning: At least two people are required to move the library chassis. Avoid putting the weight of the library chassis on the front bezel. Caution: Figure 8 Preparing the Library for Shipping Accessories kit Shipping materials Library chassis Front bezel Lift point Shipping materials Shipping carton 12 Packing the Library for Shipment [. . . ]