User manual QUANTUM PX500 USERS GUIDE 81-81290-04 A01

[. . . ] Quantum PX500 Series User's Guide, 81-81290-04 A01, August 2006, Made in USA. Quantum Corporation provides this publication "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation may revise this publication from time to time without notice. Making copies or adaptations without prior written authorization of Quantum Corporation is prohibited by law and constitutes a punishable violation of the law. [. . . ] Parallel SCSI interface - in a library with a parallel SCSI interface, you must add either a TC2201 iSCSI bridge or a FC1202 Fibre Channel bridge and configure the appropriate network (iSCSI or Fibre Channel) to include the bridge(s) and host systems. If you do not have a TC2201 or FC1202 bridge installed, the library is limited to one partition. · Native Fibre Channel interface - in a library with a native Fibre Channel interface, you must have a Fibre Channel switch available to connect to the library Fibre Channel SCB, Fibre Channel hosts, and native Fibre Channel tape drives. If you do not have a Fibre Channel switch available, the library is limited to one partition. Accessing the Partitions Page To access the Partitions page, click Partitions from the Setup page. The management frame displays the Partitions page (see figure 80). 3 Quantum PX500 Series User's Guide 122 Chapter 3 Quantum PX500 Series Remote Management Setup Figure 80 Partitions Page When the library is in surrogate mode, this area of the partitions tab changes to indicate the drive number operating as the surrogate media changer. The Partitions page contains a list of all user defined partitions and a section for either creating a partition or changing a partition's configuration and options. Clicking on a partition name in the Partition list displays a detail window listing all details for the selected partition. Creating a Library Partition To create a library partition: Note: The library must be offline to create or edit a library partition. 3 1 Enter the partition information listed in table 31 and click New to create the partition. Quantum PX500 Series User's Guide 123 Chapter 3 Quantum PX500 Series Remote Management Setup Table 31 Creating a Partition Field Partition Name Description Enter a unique name for the partition. Partition names must start with a letter (a-z or A-Z), cannot be longer than 10 characters, and cannot contain spaces or special characters. Select one or more magazines from the unassigned magazine list and move it to the assigned magazine list. Select a drive or drives from the unassigned drives list and move it to the assigned drive list. A partition MUST contain at least one drive. SCSI Logical Unit (LUN) - Enter the SCSI logical Cabinets Magazines Drives SCSI Logical Unit (LUN) or Surrogate Drive unit number for this partition. Surrogate Drive - Enter the surrogate tape drive number (logical drive number). Load Port Select a load port from the load port list if required for this partition. Select this box to automatically clean the drives in the partition when needed. Select this box to return an P-Series inquiry string to the host connected to this partition. The partition will appear to the host as an P-Series tape library. Enable Autoclean Emulate P-Series Quantum PX500 Series User's Guide 124 Chapter 3 Quantum PX500 Series Remote Management Setup Field Enable Barcode Swap Configured Slots Description Enables/disables swapping media type prefix from the back of barcode to the beginning. The configured slots option allows you to designate the number of slots available and reported to the host. Editing a Library Partition To edit a library partition: Note: The library must be offline to create or edit a library partition. 3 1 Select the partition link under the Partitions section. The area below the Partitions section displays the selected partition settings. 2 Edit the partition information as desired (refer to table 31) and click Apply to save the changes. 3 Click Clear to clear the partition settings and return to Creating a Library Partition. Quantum PX500 Series User's Guide 125 Chapter 3 Quantum PX500 Series Remote Management Setup Deleting a Library Partition There are two ways to delete partitions: 1 To delete a single library partition: a Select the partition link under the Partitions section. Note: When a partition is added, edited, or deleted the library must be rebooted for the changes to take effect. 3 b Click Remove to delete the partition. The library partition is deleted. 2 To delete all of the library partitions: a Click Remove All. All library partitions are deleted. Secure Key 3 The Secure Key tab displays when a secure user has been added to the library and the secure user is logged in. Caution: If the secure key information is lost, any tape cartridges that were secured with the lost key will be unavailable for reading or writing. To access the Secure Key page, from the Setup page, click on the Secure Key tab at the top of the page. The Secure Key page displays (see figure 81). Quantum PX500 Series User's Guide 126 Chapter 3 Quantum PX500 Series Remote Management Setup Figure 81 Secure Key Page Quantum PX500 Series User's Guide 127 Chapter 3 Quantum PX500 Series Remote Management Setup The Secure Key page is divided into the following sections: · · · · · · · · Protection Mode for Cartridges Enable/Disable Secure Key for Drives Modify Secure Key for Library Assign Secure Key to Cartridge Create Secure Key Name/Secure Key Pair Delete Secure Key Name Backup Secure Key File Upload Secure Key File Protection Mode for Cartridges Refer to figure 82 for information on Protection Mode for Cartridges. 3 Figure 82 Protection Mode for Cartridges The Protection Mode for Cartridges area defines when the secure key is used for a cartridge in a tape drive with a secure key enabled. In all modes, the secure key is used to read data from cartridges that have a pre-existing secure key. [. . . ] Utrustningen alstrar, använder och kan utstråla radiofrekvent energi och kan, om den ej Quantum PX500 Series User's Guide 243 Appendix E Regulatory Statements Notice for USA and CANADA Only installeras och används i enlighet med instruktionshandboken, orsaka störningar i radiokommunikation. Eventuella ändringar eller modifikationer av utrustningen kan ogiltigförklara användarens rätt att använda utrustningen. Användning av utrustningen i bostadsområden kan orsaka störningar och i sådana fall måste användaren bekosta de åtgärder som krävs för att åtgärda störningarna. Användningen underkastas följande villkor: 1 Enheten får inte orsaka störningar och 2 enheten måste tåla mottagna störningar, inklusive störningar som kan orsaka oönskad funktion. Meddelande för Taiwan  !" #$%&'()*+ , -. Kanada (digital utrustning) Hänvisning: Standard för störningsalstrande utrustning, ICES-003, utgåva 2 Denna klass A för digital utrustning uppfyller alla krav i de kanadensiska föreskrifterna för störningsalstrande utrustning. CISPR-22 Varning! Detta är en klass A produkt. [. . . ]