User manual QUANTUM PX500 TAPE DRIVE INSTALLATION INSTRUCTIONS 81-81301-01 B01

[. . . ] Quantum PX500 Series Library Tape Drive Installation Instructions Introduction 3 Tape Drive Numbering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Upgrade Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Unpacking the Tape Drive Installing the Tape Drives Cabling the Tape Drives Setting the Tape Drive SCSI ID 7 7 8 11 Setting the SCSI ID Using the OCP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Setting the SCSI ID from the Remote Management Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 81-81301-01 B01, May 2005 1 Quantum PX500 Series Tape Drive Installation Instructions 81-81301-01 B01 May 2005 2 Quantum PX500 Series Tape Drive Installation Instructions 81-81301-01 B01 May 2005 Introduction 0 This document provides instructions for adding a tape drive to an Quantum PX500 Series tape library. The tape drive upgrade procedure consists of the following steps: · · · · Unpacking the Tape Drive Installing the Tape Drives Cabling the Tape Drives Setting the Tape Drive SCSI ID Tape Drive Numbering 0 The Quantum PX500 Series tape library may contain up to 10 tape drives depending on the library model. [. . . ] 5 Repeat steps 1 through 4 to install another tape drive in a different location, if desired. Unpacking the Tape Drive 7 Quantum PX500 Series Tape Drive Installation Instructions 81-81301-01 B01 May 2005 Figure 4 Installing a Tape Drive Tape drive 1 Captive screw Tape drive 2 PX502 shown Captive screw Proceed to Cabling the Tape Drives. Cabling the Tape Drives After the tape drive(s) have been installed, you must connect SCSI cables to each drive. To cable the tape drives: 0 1 Connect the host computer(s) to the library and tape drives as shown in figure 5 for a PX502 library, figure 6 for a PX506 library, and figure 7 for a PX510 library. 8 Cabling the Tape Drives Quantum PX500 Series Tape Drive Installation Instructions 81-81301-01 B01 May 2005 Figure 5 Cabling the Tape Drives in a PX502 Library Host computer SCSI terminator SCSI jumper cables Figure 6 Cabling the Tape Drives in a PX506 Library SCSI jumper Host computer SCSI jumper Host computer SCSI terminators SCSI jumper Host computer SCSI jumper Cabling the Tape Drives 9 Quantum PX500 Series Tape Drive Installation Instructions 81-81301-01 B01 May 2005 Figure 7 Cabling the Tape Drives in a PX510 Library SCSI jumper SCSI jumper Host computer Host computer SCSI jumper Host computer SCSI terminators SCSI jumper Host computer SCSI jumper Host computer 10 Cabling the Tape Drives Quantum PX500 Series Tape Drive Installation Instructions 81-81301-01 B01 May 2005 Setting the Tape Drive SCSI ID The next step in the installation procedure is to set the required SCSI ID for the new tape drive. It is only necessary to perform the steps in this section if you need to set the tape drive SCSI ID to an ID other than the default. 0 There are two ways to set the tape drive SCSI ID: · · Setting the SCSI ID Using the OCP Setting the SCSI ID from the Remote Management Pages Setting the SCSI ID Using the OCP To set the tape drive SCSI ID on an PX500 Series library with an LCD: 0 1 From the operator control panel (OCP), press Setup from the Home screen. The OCP displays the Setup screen (see figure 8): Figure 8 Setup Screen Enter 2 Use the up and down arrows to highlight Cabinet and press Enter. The Cabinet screen displays (see figure 9): Figure 9 Library Options Screen 3 Use the up and down arrows to highlight Host bus and press Enter. The Host bus screen displays (see figure 10): Setting the Tape Drive SCSI ID 11 Quantum PX500 Series Tape Drive Installation Instructions 81-81301-01 B01 May 2005 Figure 10 Host Bus Options Screen 4 Use the up and down arrows to highlight the tape drive receiving the new SCSI ID and press Enter. 5 Use the up and down arrows to select a SCSI ID and press Enter to set the ID. 6 When you have completed setting the SCSI IDs, press Exit to return to the Cabinet screen. 7 From the Ops screen, use the up and down arrows to highlight Drive Operations and press Enter. The Drive Operations screen displays (see figure 11): Figure 11 Drive Operations Screen 8 Use the up and down arrows to select a tape drive and press Enter. The tape drive powers down and returns to the Drive Operations screen. The tape drive installation is complete. Setting the SCSI ID from the Remote Management Pages 0 To set the tape drive SCSI ID on a PX500 Series library from the remote management pages: Note: The library must be off-line during this procedure. 1 On the host computer, open the internet browser software. [. . . ] 10 Enter the new tape drive number 11 Select Power on and click Apply. The tape drive installation is complete. 14 Setting the Tape Drive SCSI ID [. . . ]