User manual QUANTUM P1000PAK

[. . . ] 0 March 1999 ATL P1000 Series Library Unpacking Instructions 0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Selecting an Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Floor Space. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Floor Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Floor Strength and Inclination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Overhead Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Power and Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Power Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Rack Current Rating Consideration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Unpacking the Library. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Unloading Space Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Uncrating the Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Installing the Slide Assembly in the Rack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Verifying the Rack Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Rack Current Rating Consideration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Determining the Mounting Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Installing the Slide Assembly in the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 1 ATL P1000 Series Library Unpacking Instructions Document 6221100-02, Ver. 0 March 1999 Adjusting the Slide Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Removing the Library from the Pallet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Removing a Stand-alone Library from the Pallet . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Adjust the rear mounting brackets so that the distance from the front mounting brackets to the rear mounting brackets is slightly greater than the depth of the rack. Insert the slide assembly into the rack: a b 2 3 4 Lift the slide assembly and tilt it sideways. Insert the back end of the slide assembly into the front of the rack, keeping the slide assembly above the temporary support screws. When the rear brackets clear the rear retma rails, turn the slide assembly right side up. Place the slide assembly in the rack so that each bracket rests on a temporary support screw. c d 5 Secure the front mounting brackets to the front retma rails, using four 10-32 x 3/4 in. Adjust the rear mounting brackets so they are flush with the outside of the rear retma rails. Installing the Slide Assembly in the Rack 15 6 ATL P1000 Series Library Unpacking Instructions Document 6221100-02, Ver. 0 March 1999 Procedure (continued) 7 Remove the two 10-32 x 3/4 in. temporary support screws from the front retma rails and install them in the left and right rear mounting brackets to secure the rear mounting brackets to the rack retma rails. temporary support screws from the rear retma rails and use them to finish securing the rear mounting brackets to the rack retma rails. 8 Note: Do not tighten the nuts securing the rear mounting brackets to the slide assembly. You will tighten these during the following procedure, "Adjusting the Slide Assembly. " 9 Remove the four temporary support screws. Figure 10 Installing the Slide Assembly in the Rack Mounting screws Retma rails Support screw Rear mounting bracket Slide assembly Mounting screws Front mounting bracket Support screw 16 Installing the Slide Assembly in the Rack ATL P1000 Series Library Unpacking Instructions Document 6221100-02, Ver. 0 March 1999 Adjusting the Slide Assembly Now that the slide assembly is installed in the rack, verify that: 10 The front door of the rack opens and closes freely. (76. 2 cm) from the front of the rack. If the slide assembly and rack do not meet the above requirements, complete the procedures in this section to adjust the slide assembly. The number of adjustments required varies from rack to rack. Adjusting the Slide Assembly on the Mounting Brackets 10 To adjust the slide assembly on the mounting brackets: Procedure 1 Loosen the outer nuts on both sides of the slide assembly (see figure 11). These nuts secure the mounting brackets to the slide rails. Figure 11 Loosening the Outer Nuts Outer nuts Outer nuts 2 Move the slide assembly forward or backward as necessary. Installing the Slide Assembly in the Rack 17 ATL P1000 Series Library Unpacking Instructions Document 6221100-02, Ver. 0 March 1999 Procedure (continued) 3 When the slide assembly is in the desired position, tighten all outer nuts: a Pull the slide assembly tray forward until you can access the four rear screws. Tighten each of the four rear nuts by holding the nut with an 11/32 inch open-ended wrench and then tightening its corresponding screw with a Phillips screwdriver. Extend the slide assembly out of the rack until both the intermediate and inner channels of the slide rails lock (see figure 12). The intermediate channels are secured by the intermediate channel locks, which are located on the inner, back edge of the intermediate channels. b c d Release the intermediate channel locks by rotating them upward slightly. Note: Do not release the inner channel locks. e Push the slide assembly back into the rack until the access hole on the inside of the intermediate channel exposes a screw. Use a Phillips screwdriver to tighten the screw while holding its corresponding nut with an 11/32 inch open-ended wrench. The inner channel locks are located on the outer, back edge of the inner channels. f g h i 4 Push the slide assembly tray back into the rack. Check for clearance. If necessary, repeat this procedure to adjust the slide assembly further. 18 Installing the Slide Assembly in the Rack ATL P1000 Series Library Unpacking Instructions Document 6221100-02, Ver. 0 March 1999 Figure 12 Slide Assembly Tray, Fully Extended Intermediate channel lock Access hole Intermediate channel Inner channel lock Inner channel Adjusting the Slide Assembly Tray on the Slide Rails 12 To adjust the slide assembly tray on the slide rails: Procedure 1 Loosen the inner nuts on both sides of the slide assembly (see figure 13). [. . . ] This releases the latches securing the load pack. 2 Still holding the load pack handles, pull the load pack forward and out of the library. Repeat steps 1 and 2 to remove the bulk pack. 3 28 Removing the Internal Packing Materials ATL P1000 Series Library Unpacking Instructions Document 6221100-02, Ver. 0 March 1999 Figure 19 Removing the Load and Bulk Packs Handles Removing the Shipping Restraint To remove the shipping restraint: 19 Note: The shipping restraint that protects the extension axis assembly is attached to the bottom drive shelf and fits over the supports for the load and bulk packs. Procedure 1 Grasp the front edge of the shipping restraint and carefully push inward at both corners while lifting it up at an angle (see figure 20). The tab on the shipping restraint (between the mounting blocks for the load and bulk packs) pops up, releasing the shipping restraint from the load pack shelf. [. . . ]