User manual QUANTUM L200GUID

[. . . ] Quantum|ATL PowerStor L200 Series Library User's Guide 6322500-04 Ver. 0 Quantum|ATL PowerStor L200 Series Library User's Guide, 6322500-04, Ver. provides this publication "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum|ATL is the generally known alternative designation of ATL Products, Inc. [. . . ] Enter also toggles each of the Y and N options. 5 Press Select to return to the main menu. Optional Autoclean Mode 3 If the optional autoclean is enabled, the time that a SCSI Move Media command takes to complete increases from approximately 20 seconds to 60 seconds because the library must wait until calibration is complete. If cleaning is required, the typical time increases to a maximum of 10 minutes while the drive is cleaned. Press Enter to enable AutoClean: Y. When AutoClean is enabled, the status of slot 7 becomes unviewable. After the manual cleaning cycle is complete, the second line of the OCP will display an idle message. After the initialization process is complete, set the AutoClean parameter to N. The cleaning cartridge may then be ejected. 34 Quantum|ATL PowerStor L200 Series Library User's Guide Chapter 3 Operator Control Panel Information Firmware Updates 3 Following a library firmware code update, the mode settings will revert to their defaults: Random Access: Selected Bar Code Read: N Sequential Access: Not Selected Autoload Cart: N Sequential Circ: Not Selected AutoClean: N Set Auto Unload Cart: Y Information The Information?option displays the device revision number, software revision number, library cycle count and library error count (see table 8). 3 Table 8 Information Messages Information Type Ldr Hw Rev Ldr Rw Rev Ldr Mech Rev Lib Hw Rev Lib Fw Rev Drive Rev Library Life Cycle Count Message ## ## ## ## ## ## ## Notes Device hardware revision level Device firmware revision level Library revision level Library hardware revision level Library firmware revision level Drive firmware revision level Count starts from completion of first POST decimal format hex format Quantum|ATL PowerStor L200 Series Library User's Guide 35 Chapter 3 Operator Control Panel Code Update Information Type Current Cycles Ldr Err: Message ## Notes Count starts from completion of most recent POST Library error count ## decimal format hex format Code Update 3 The Code Update?option displays what tape drive is installed and installs new microcode for the tape drive through the cartridge or the host (see table 9). Table 9 Code Update Messages Option Update Drive # Message Update Drive 0 Note Press ENTER to start the automated code updating process for the selected drive Revision level is in decimal format Revision level is in hex format. (. ) T (test) V (release) T (test) V (release) (h) Installing New Drive Microcode 3 For detailed microcode update procedures, contact Quantum|ATL Customer Support or your service representative. 36 Quantum|ATL PowerStor L200 Series Library User's Guide Chapter 3 Operator Control Panel Tests Tests To move through the Tests?option: · If Previous or Next is pressed during a test, the next message test is displayed along with the message: A Test is Active When the original test is completed the next test will start. · If Enter is pressed during a test in progress, the test will be terminated. Press Enter to restart a test from the beginning, once the termination process completes (see table 10). 3 The TESTS?option controls the library internal self-test functions. Table 10 Tests Options Description Elevator Test Tests the library elevator function. This is a one cycle test. Messages Notes Active or Aborted The CHM is positioned to each available data transfer element (drive) or data storage element (magazine slot). If the magazine is not present, the CHM cannot be positioned to those slots. This test is functionally equivalent to SCSI Position to Element commands. Load/Unload Test Randomly loads and unloads cartridges into the tape drive. This is a one cycle test. Active or Aborted Unloads any cartridge in the drive, inserts a cartridge in the drive, and replaces the cartridges in their slots. The drive is left empty. Quantum|ATL PowerStor L200 Series Library User's Guide 37 Chapter 3 Operator Control Panel Tests Description Long Ld/ Unld Test Randomly loads and unloads cartridges into the tape drive repeatedly, until the test is aborted by pressing the Enter button on the OCP. Messages Notes Active or Aborted Loads and unloads the drive with cartridges from random slots. 38 Quantum|ATL PowerStor L200 Series Library User's Guide Chapter 4 4Using the Library This chapter describes how to use the library: · · · Using the Library Door Using Tape Cartridges Using the Cartridge Magazine Using the Library Door 4 The library holds one removable 6-cartridge magazine. They are located behind the removable magazine, to the left of the tape drive. Quantum|ATL PowerStor L200 Series Library User's Guide 39 Chapter 4 Using the Library Using the Library Door Figure 11 Slot Locations Internal drive Internal slots 7-8 Magazine slots 1-6 Caution: To prevent cartridge jams, use the space on the front of the cartridge for labels. Damage to the library may occur if the CHM is blocking access to the fixed cartridge slot. Note: Use physical slot 1 (OCP slot 0) when performing a drive microcode update; use physical slot 8 (OCP slot 7) when using the optional AutoClean mode. Note: Insert and remove all cartridges from the front of the magazine. 40 Quantum|ATL PowerStor L200 Series Library User's Guide Chapter 4 Using the Library Using the Library Door Opening the Library Door To open the magazine door, using the OCP: 4 1 Press Select until the message EJECT/UNLOCK?Press Enter to remove any cartridge from the drive and display the message Open Doors!. [. . . ] EOT End of tape. 88 Quantum|ATL PowerStor L200 Series Library User's Guide Glossary element A SCSI designation for any device or bin in the library that can hold a DLT cartridge. SCSI elements include storage bins, tape drives, load port bins, and the gripper. error message A message appearing on the host computer or library control panel screen informing you that the program was unable to carry out the desired operation. execute To carry out the instructions in a computer program. Federal Communications Commission governing electromagnetic emissions in a commercial environment. FRU Field-replaceable unit--A term given to parts of the library that are designed to be replaced onsite. [. . . ]