User manual QUANTUM FREEXWIRE FW11

[. . . ] Hot shoe adapter with additional sync inputsused with QF series TTL adapters FREEXWIRE hot shoe adapter to mount FW9T or FW10 on camera shoe wireless links that can be turned on or off to change lighting and camera activation independent channels for separate FREEXWIRE setups operating in the same area a flash close to the camera and connected with a sync cord a flash at a distance from the camera and wirelessly synchronized 3 1. 0 Introduction We introduce the newest additions to the FREEXWIRE system: Receivers FW8R, FW7Q and Transmitter FW9T. FW7Q is dedicated to, and designed for any Qflash 4 or 5 series flash. FW7Q, FW8R and FW9T are fully compatible with all other FREEXWIRE system components. Transceiver FW10 may be upgraded for additional features of Section 7. 0. [. . . ] Any other screw used must protrude not more than 3/4" (2 cm) into the FREEXWIRE case, or you will damage FREEXWIRE!When mounting the FW12 or FW11 to a Dead Shoe (model 512) it will be necessary to connect a sync-in cable for FW9T units, or sync-out cable for FW8R units. See Appendices A and B. 9 5. 3: Direct Hot Shoe Mounting with FW12 or FW11 Connect the Hot Shoe Adapter FW12 or (Uni-Mod FW11) to a Transmitter FW9T and slip it into a camera hot shoe. The purpose of the Hot Shoe Adapter is only to provide hot shoe mounting and sync from a camera to a Transmitter FW9T. FW11 or FW12 will not provide TTL control -- see Appendix D for selection of QTTL and other TTL adapters. A Receiver FW8R mounted to FW11 or FW12 on a camera shoe will have no connection to the shutter release. If you desire wireless shutter release, connect a separate Shutter Release Cord (see appendix C) between the FW8R MD socket and the shutter release connection on the camera. FW7Q plugs into the lower Accessory socket of Qflash, as shown in the diagram. For added stability a hook-and- loop pad is mounted on the back of Receiver FW7Q. One part of this pad will be attached to the Qflash housing as follows: Note where the hook and loop pad will come into contact with the Qflash housing when FW7Q is plugged into the lower Accessory socket. Remove the adhesive liner from the pad (without touching the MOUNTING FW7Q adhesive), and align and mount FW7Q. This set up does not require a camera with TTL capability nor a TTL Adapter, only local and remote Qflashes. 9. 1 Transmitter FW9T set-up: Connect an FW31 cable from Transmitter FW9T to Qflash. Connect a Sync-in cord from camera PC nipple to Transmitter FW9T Sync -in. Set the local Qflash to Auto mode. FW31 14 15 9. 2 Receiver FW8R or FW7Q: Mount and connect one or more of these receivers as in Section 7. 2. The remote TTL Qflashes will expose to the setting of the local "Auto" Qflash. 9. 3 Additional features with Qflash 4 and 5 series & QTTL Adapters: Many other Wireless Auto features are available when a Qflash 4 or 5 series is connected to the camera with a D or Dw series Adapter. The available features include: Wireless ratio control between Qflashes; Wireless auto-fill; Flash f/# tracking the camera's f/# setting as it changes; Sensor limit with any of the preceding modes. Full details of these features are found in the operating manuals for Qflash 4 or 5 and D series QTTL adapters. Operating manuals can be found at qtm. com if needed. 11. 0 FREEXWIRE Performance Guide How to maximize performance, troubleshoot, and answer questions about Quantum's FREEXWIRE Wireless Photo Control System. If for some reason we don't have an answer in this guide, please email, fax, write or call Customer Service for further assistance. Good radio performance depends on several factors: The orientation of a radio and antenna, the presence of other radio signals which may interfere, and the presence of objects which may interfere. [. . . ] FW31 Accy cable 18" (. 5m) 434 Sync-out cord 18" (. 5m) 435 Sync-out cord 4' (1. 2m) 534 Sync-out cord 18" (. 5m) 535 Sync-out cord 5' (1. 5m) 536 Sync-out cord 18" (. 5m) 537 Sync-out cord 5' (1. 5m) 541 Sync-out cord FREEXWIRE Accy conn. FREEXWIRE mini-phone To Your flash Qflash Accy Flash PC nipple Flash PC nipple 2 prong 2 prong 2 prong + pin 2 prong + pin 2 prong + pin Notes Supplied by flash mfg. For Qflash and some studio flash For Qflash and some studio flash For Studio flash -2 prong socket For Studio flash -2 prong socket For Qflash and some studio flash For Qflash and some studio flash For Qflash and some studio flash Appendix C - Motor Drive cords from FREEXWIRE to camera Model 451 452 453 454 456 458 459 463 464 465 466 467 FW41 FW42 FW43 FW44 Camera Nikon MD2/4/12/15, 8008s, F4S Hasselblad ELM, ELX Canon, Olympus, Hasselblad H-1 Mamiya RZ67, RZ67 II, 645 Super, 645 Pro Leica R3, R5, R6, R6-2, R7, RE Minolta 5000, 7000, 9000, 5000i, 7000i, 8000i, 5Xi, 7Xi, 9Xi, 700si, Maxxum - 7, 9 Canon EOS A5, A2E, A2, 1, 1N, 620, T90, Rebel 300D Bronica SQAI Rollei, 6002, 6003, 6006, 6008, SLX Hasselblad 503CW/CXi Canon EOS 3, 1V, D30, D60, 10D, 1D, 1Ds, 1D Mark II Mamiya 645AF Contax 645, Canon Elan 2, 2E, 7, 7E, Rebel 2000, XI Lite, Rebel 300D, Hasselblad H-1 Maxxum 7, 9 Canon 1v, 3, D2000, D30, D60, 10D, 20D, 1D, 1Ds, 1D Mark II Nikon D1, D1H, D1X, D2H, D2X, F5, N90/s, F90x, F100 / Kodak DCS 760, Fuji S3 Mamiya 645AF Canon EOS 1, A2, A2E, AS, 1N, 620, T90 Pentax 645N and all Autofocus SLR Cameras except Z-1p Notes N90s, F5 need Nikon adapter MC25 See other Canon selections Two step MD cord Two step MD cord Two step MD cord Two step MD cord Two step MD cord Two step MD cord Two step MD cord 434 435 541 FW31 FW45 FW46 FW47 FW11 or FW22 540 534 535 536 537 YOUR FLASH SYNC CABLE 20 21 Appendix D -- QTTL and TTL Wireless Adapters for Transmitter FW9T These Adapters connect to a FREEXWIRE TX and provide wireless QTTL/TTL exposure control. D Series *** QTTL Adapters D10w D12w D13w QF Series** TTL Adapters QF10 QF11 QF12 QF13N QF14 QF15 QF16 QF17 QF18 QF19 QF20 QF22 QF23 QF24 QF25 FW Series* TTL Adapters Cameras Olympus, Practica Minolta X series Nikon, Fuji S2, S3 Canon Minolta Xi series Contax Leica Pentax Rollei Hasselblad Bronica Mamiya 645 ProTL Leica R8 Contax 645 Mamiya 645AF, 645AFD Appendix F - Specifications Size: FREEXWIRE FW8R/FW9T: 3. 6 x 2. 3 x 1. 1 in. [. . . ]