User manual QUANTUM FC1202 USERS GUIDE 81-81354-01 A01

[. . . ] Quantum FC1202 User's Guide, 81-81335-01 A01, June 2005, Made in USA. Quantum Corporation provides this publication "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation may revise this publication from time to time without notice. Making copies or adaptations without prior written authorization of Quantum Corporation is prohibited by law and constitutes a punishable violation of the law. [. . . ] The firmware download is complete. Perform Configuration The Configuration Menu is used to configure the FC1202. 2 Quantum FC1202 User's Guide 49 Chapter 2 FC1202 Bridge Serial/Telnet User Interface Perform Configuration Figure 33 FC1202 Configuration Menu Note: The FC1202 is shipped with a configuration of default settings that is acceptable for most system environments. After any configuration changes are made, select A) Save Configuration to record the changes. If the configuration has been modified to meet company-specific needs, back up the company-specific configuration to an external file. If necessary, these settings can later be restored to the FC1202. Configuration Menu options: · · · · · · · · Baud Rate Configuration changes the baud rate on the serial port. Fibre Channel Configuration configures the settings for the Fibre Channel port. Parallel SCSI Configuration configures the settings for the SCSI buses. Device Mapping modifies map and host settings. settings. Trace and Event Settings Configuration modifies trace and event filter Real-Time Clock Configuration sets the system clock. Active Fabric Configuration changes the number of controller LUNs. 50 Quantum FC1202 User's Guide Chapter 2 FC1202 Bridge Serial/Telnet User Interface Perform Configuration · · · · Save Configuration saves changes to memory. configuration. Restore Last Saved Configuration reverts to the previous Reset and Save Configuration to Factory Defaults resets all Return to Main Menu goes back to the previous screen. configuration options to the factory defaults. Because the Configuration Menu is the primary menu in the UI, each Configuration Menu option is discussed in a separate section. Baud Rate Configuration 2 In the Configuration Menu, select Baud Rate configuration to change the baud rate used on the serial port. Figure 34 is an illustration of the Baud Rate Configuration Menu. Figure 34 Baud Rate Configuration Menu Options include: · · · · · 9600 19200 38400 57600 115200 Quantum FC1202 User's Guide 51 Chapter 2 FC1202 Bridge Serial/Telnet User Interface Perform Configuration Note: The asterisk (*) symbol indicates the current setting for the baud rate. If the Autobaud feature is being used, it is not necessary to set a baud rate. Ethernet Configuration 2 In the Configuration Menu, choose Ethernet Configuration to set up the Ethernet network. When this option is selected, the Ethernet Configuration Menu is displayed. Current Ethernet settings are displayed, along with available Ethernet configuration options. Figure 35 is an illustration of the Ethernet Configuration Menu. Figure 35 Ethernet Configuration Menu To view or change configuration settings: 1 Select a menu option 2 Make the configuration changes 3 Select X) Return to previous menu 4 Select A) Save Configuration to record the changes. Ethernet Configuration Menu options: 52 Quantum FC1202 User's Guide Chapter 2 FC1202 Bridge Serial/Telnet User Interface Perform Configuration · · · · Change IP address (default: 1. 1. 1. 1) changes the FC1202 IP address. Change IP Subnet Mask (default: 255. 255. 255. 0) changes the FC1202 Subnet mask. Ethernet network. Change IP Gateway (default: 0. 0. 0. 0) changes the IP gateway for the Change Ethernet Physical Address changes the Ethernet physical address (MAC address). Caution: If this configuration setting is incorrectly set, processing difficulties may occur. Before changing this setting, evaluate the need for the change and verify the desired setting. Backing up the FC1202 configuration to an external file before making changes to this setting is recommended. · Toggle Ethernet Mode changes the Ethernet mode. Options include: · · · · · 10 Mb/s only 100 Mb/s (half duplex) only 100 Mb/s (full duplex) only 10/100 MPS (Auto-Neg. ) Change Hostname changes the name of the host server. The name can be any combination of alphanumeric characters, up to eight characters. · Configuration Protocol. Toggle DHCP Configuration enables or disables support for Dynamic When DHCP is enabled, the FC1202 will request a dynamic IP address from the DHCP server on the Ethernet network. Some DHCP servers allow a lease reservation to be set up for an IP address by providing the server with the Ethernet MAC address. This setup can be useful for remote management of the FC1202 such Quantum FC1202 User's Guide 53 Chapter 2 FC1202 Bridge Serial/Telnet User Interface Perform Configuration as Telnet or Visual Manager, because the method of setting up a lease reservation varies depending on the DHCP server being used. Note: To use the DHCP feature, a DHCP server must be operational on the Ethernet network. If the DHCP feature is used when there is no DHCP server, DHCP standards require that the FC1202 wait three minutes for a response from a DHCP server before timing out. · · Change SNMP Settings is not supported. 9) Change Security Settings changes security settings, including the user name and password. The default user name is root and the default password is password. [. . . ] If no devices are listed, verify the Interface Controller configuration, Fibre Channel HBA configuration, and cabling. If devices are listed, verify the Fibre Channel HBA mapping mode or the AL_PA addresses. The Windows 2000 driver is the device driver installation file (called an INF file) needed by the MS Windows 2000 Operating System. The Interface Controller needs no driver in reality, as the HBA in the Host PC Quantum FC1202 User's Guide Verifying Windows 2000 Driver 3 88 Chapter 3 Troubleshooting Basic Troubleshooting manages it. [. . . ]