User manual QUANTUM DLT-V4 SATA HBA COMPATIBILITY

[. . . ] DLT-V4 SATA Notes 1 Tested HBA's and Onboard Chipsets HBA / Motherboard Adaptec ASH 1205SA Dell Onboard - Intel ICH5 82801EB Gateway Onboard - Intel ICH7R 82801GB-27C0 White Box PC Onboard - ABIT IC7 (ICH5) Promise SATAII150 TX4 SIIG SD-SATA3112-150R Silicon Image SIL3112 Silicon Image SIL3114 Silicon Image SIL3124 Silicon Image SIL3512A HBA Firmware / BIOS A. 2. 11 N/A N/A N/A 1. 00. 0. 34 4. 2. 02 4. 1. 50 5. 0. 18B 6. 0. 17 4. 3. 47 See Section 2. 3 See Section 2. 3 See Section 2. 3 See Section 2. 3 See Section 2. 2 Comments 2 Troubleshooting Tips 2. 1 Motherboard ICH 5/6/7 SATA: 1 If the onboard controller is designed to control both SATA and IDE (ATA) devices, changes in the BIOS configuration are likely for all devices to function properly. [. . . ] In the Current Transfer Mode drop-down box, select DMA if Available if the current setting is "PIO Only. " If the drop-down box already shows "DMA if Available" but the current transfer mode is PIO, then the user must toggle the settings. That is: Change the selection from "DMA if available" to PIO only, and click OK. Then repeat the steps above to change the selection to DMA if Available. 2. 2 Example Configuration (BIOS): 1. Motherboard: ABIT IC7 (ICH5) · 2 x ATA/100 IDE connectors (ICH5) · 2 x SATA 1. 5Gb connectors (ICH5R) with RAID 0 support · Serial ATA RAID 0 3. System Devices: · CDROM - IDE Master (Secondary IDE Channel) · HDD - IDE Master (Primary IDE Channel) · HDD - IDE Slave (Primary IDE Channel) · DLT-V4 - SATA Slave (Secondary IDE Channel) - Attached to port labeled "SATA 1" · Note: With mixed IDE / SATA devices, requires IDE, Master/Slave Setup. BIOS Configuration: · IDE Bus Master: Enabled · OnChip IDE-1 Controller: Enabled Master Drive PIO Mode: Auto Slave Drive PIO Mode: Auto Master Drive Ultra DMA: Auto Slave Drive Ultra DMA: Auto · OnChip IDE-2 Controller: Enabled Master Drive PIO Mode: Auto Slave Drive PIO Mode: Auto Master Drive Ultra DMA: Auto Slave Drive Ultra DMA: Auto · OnChip Serial ATA Setting OnChip Serial ATA mode: IDE OnChip Serial ATA: Combined Mode Serial ATA 1 Mode: IDE-2 Slave Serial ATA 2 Mode: IDE-4 Master 5. Motherboard SATA HBA: If the motherboard SATA controller is an onboard HBA (Sil3112) the DLT-V4 tape device will function properly as the connection is point-to-point and the ® Quantum Corporation. All rights reserved. 2 Microsoft Windows atapi. sys is not included in the driver stack. 2. 3 Example Configuration (BIOS) 1. [. . . ] phone 949. 856. 7800 fax 949. 856. 7799 European Headquarters Quantum Corporation 3 Bracknell Beeches Old Bracknell Lane West Bracknell Berkshire RG12 7BW United Kingdom phone +44 1344 353500 fax +44 1344 353510 Asia Pacific Level 3 200 Creek Street Brisbane, Qld 4000 Australia phone +61 7 3839 0950 fax +61 7 3839 0955 ® Quantum Corporation. [. . . ]