User manual QUANTUM DAT 320 QUICK GUIDE

[. . . ] · A USB 2. 0 port · 5. 25-inch half-height bay (for internal drive) · Backup application software that supports the internal tape drive. For a list of the latest backup software applications tested with the internal DAT 320 tape drives, please visit our Web site at http://www. quantum. com/ServiceandSupport/ Index. aspx# Unpacking and Inspecting the Drive Before you unpack the contents of your drive package, inspect the shipping containers for damage. When you unpack the package, compare the items received with those on the packing list. If any item is missing or damaged, please contact your place of purchase immediately. 2 Before Installing the DAT 320 Tape Drive in Your System DAT 320 Required Tools The following is a list of the tools you will need. [. . . ] These may be metal or plastic rails attached to the filler panel of the server's drive bay. The rails may be attached to the filler panel by screws of a different thread/size type and these should not be used. If in doubt, refer to your server documentation. Mounting Screws Other server models only require the use of special locating screws with no mounting rail. Position the screws (see Figure 1). Figure 1 Attaching Mounting Screws 4 Installing the Internal DAT 320 Tape Drive in Your Server DAT 320 2 Attach the appropriate mounting hardware. · If you are installing on a server that requires a tray, place the tape drive in the tray. · If you are installing in a server that requires mounting rails, fasten the rails to the tape drive. · Some servers have snap-on mounting rails attached to the filler panel. These can be removed and attached to the tape drive with screws. Installing the Tape Drive To install the tape drive: 1 Slide the tape drive into the open bay aligning the tray or rails with the slots in the bay (see Figure 2). Figure 2 Installing the Tape Drive If your server does not use mounting hardware, check that the holes in the chassis are aligned with the holes in the side of the tape drive. Do not secure the drive at this point because you may have to move the drive to get the cables into place. Installing the Internal DAT 320 Tape Drive in Your Server 5 DAT 320 Quick Start Guide Attaching the USB Cable Decide Which Cable to Use There are several options for connecting the tape drive to your server: To an . standard USB cable standard USB cable Notes May be connected to the server's system board or an internal USB card. Cable routing kit is required. Connecting the USB Cable from the Tape Drive to the Server To an Internal USB 2. 0 Port 1 Use the schematic on the inside of the server panel to check whether your server has an internal USB 2. 0 port and locate its position. · A standard 5-pin USB Type B cable is provided with the tape drive (see Figure 3). Figure 3 Connecting to an Internal USB Port 6 Installing the Internal DAT 320 Tape Drive in Your Server DAT 320 To an External USB 2. 0 Port Purchase a special USB cable and Cable Routing Kit. The Cable Routing Kit consists of a bracket with attached cable on one side that connects to the server's external port and a Type A USB socket on the other side. Make sure you orientate the bracket correctly when you fit it (see Figure 4). Make sure the cable is outside of the server and connect it to the server's external USB port (see Figure 4). 3 Attach the standard USB cable to the bracket (type A connector) (see Figure 4). Figure 4 Connecting the USB Cable Type B connector to tape drive Type A connector on inside of bracket Type A connector to server's external USB port Attaching the Power and USB Cables to the Tape Drive Note: The drive is not powered from the USB bus. 1 Attach the USB cable to the tape drive (Type B connector). Installing the Internal DAT 320 Tape Drive in Your Server 7 DAT 320 Quick Start Guide 2 Attach a spare cable from the server's internal power supply to the power connector (see Figure 5). Figure 5 Attaching the Power Cable USB cable to server's external USB Port Power cable Server's power supply Tape drive Power cable Securing the Drive Note: The server latches and side views of your server model may not be exactly the same as shown in the illustrations. Please refer also to your server documentation. 8 Installing the Internal DAT 320 Tape Drive in Your Server DAT 320 Mounting Hardware Used 1 Use M3 screws. [. . . ] with details and exceptions for each member country Taiwan BSMI certification, CNS 14336 * IECEE member nations include: Austria, Australia, Belgium, Brazil, Canada, China (PR), Czech Republic, Denmark, Finland, France, Germany, Hungary, Ireland, Israel, Italy, Japan, Netherlands, Norway, Poland, Singapore, Slovakia, Slovenia, Spain, Switzerland, United Kingdom, and USA. Jotta asiakasta Suomessa Laite on liitettava suojakosketinpistorasiaan For kunder i Norge Apparatet ma tilkoples jordet stikkontakt Dette produktet kan tilkobles et IT strøm distribusjonssystem För kunder i Sverige Apparaten skall anslutas till jordat uttag Electromagnetic Compatibility (EMC) Compliances The DAT 320 Tape Drives are EMC compliant with the following regulatory organizations and codes in the countries indicated: Country Australia/New Zealand Canada Regulatory Organization Australian Communications and Media Authority (ACMA) Industry Canada Digital Apparatus - Interference Causing Equipment Standard (ICES-003) CE Compliant to: AS/NZA 3548 (same as CISPR 22) ICES-003 Digital Apparatus EU member nations Emissions per CISPR 22, EN55022 and Immunity per CISPR 24, EN55024 VCCI Japan Voluntary Control Council for Interface (VCCI) 12 Electromagnetic Compatibility (EMC) Compliances DAT 320 Country Taiwan United States Regulatory Organization Bureau of Commodity Inspection and Quarantine (BSMI) Federal Communications Commission (FCC) Compliant to: BSMI EMC certification, CNS 13438 Title 47: Code of Federal Regulations, Part 15, Subpart B (47CFR15B) Jotta asiakasta Suomessa Laite on liitettava suojakosketinpistorasiaan For kunder i Norge Apparatet ma tilkoples jordet stikkontakt Dette produktet kan tilkobles et IT strøm distribusjonssystem För kunder i Sverige Apparaten skall anslutas till jordat uttag Note: Use these drives only in equipment where the combination has been determined to be suitable by an appropriate certification organization (for example, Underwriters Laboratories Inc. You should also consider the following safety points: · Install the drive in an enclosure that limits the user's access to live parts, gives adequate system stability, and provides the necessary grounding for the drive. · Provide the correct voltages (+5 VDC and +12 VDC) based on the regulation applied--Extra Low Voltage (SEC) for UL and CSA, and Safety Extra Low Voltage for BSI and VDE (if applicable). Electromagnetic Compatibility (EMC) Compliances 13 DAT 320 Quick Start Guide *6-66928-01* 14 6-66928-01 Rev B September 2010 For assistance, contact the Quantum Customer Support Center: USA: 800-284-5101 (toll free) or 949-725-2100 EMEA: 00800-4-782-6886 (toll free) or +49 6131 3241 1164 APAC: +800 7826 8887 (toll free) or +603 7953 3010 Worldwide: http://www. quantum. com/ServiceandSupport About Quantum Preserving the World's Most Important Data. [. . . ]