User manual QUANTUM ATL P4000 UNPACKING INSTRUCTIONS V2 REL 0

[. . . ] The library power requirements may require modification of the facilities existing power capabilities by a qualified electrician. The required wall outlet for the United States and Canada is rated at 125V 20A (see figure 4). Figure 4 Wall Outlet Wall outlet NEMA 5-20R rated 125V 20A Neutral Ground Line The dedicated wall outlet and a 20 amp circuit breaker must provide power to the ATL P4000 library only. Outside North America, replace the supplied power cord with a harmonized 3 x 1. 5 mm2 power cord that is approved by the country where used, and install the appropriate wall outlet. More information on the electrical requirements is provided in the ATL P4000 Pre-Installation Site Survey Instructions. Caution: The ATL P4000 library must be connected to a grounded electrical outlet. Selecting an Installation Location 5 Quantum ATL 4000 Library Unpacking Instructions Document 6434005-02, Ver. [. . . ] Report any damage to the shipper. Caution: The ATL P4000 weighs approximately 1072 pounds (486 kg), without drives. It is strongly advised to use at least two people to move and install the library. Unboxing the Library 0 To unbox the library: 1 Choose the unloading side. The ATL P4000 may be unloaded from either the right or left side of the pallet. 2 Verify the minimum floor space requirements. Note: Uncrating the library requires a minimum of 3 feet (91 cm) on all sides. For the side being used for the ramp, uncrating the library requires 9 feet (2. 74 m). Figure 5 shows the minimum floor space required by the ATL P4000 at its uncrating site. The minimum height required for unpacking the ATL P4000 is 85 inches (2. 16 meters). 8 Unpacking the Library Quantum ATL 4000 Library Unpacking Instructions Document 6434005-02, Ver. 0 August 2002 Figure 5 Minimum Floor Space Requirements-- Uncrating Site 3 ft (91 cm) 3 ft (91 cm) 9 ft (2. 74 m) for ramp extensions 3 ft (91 cm) 9 ft (2. 74 m) for ramp extentions 3 ft ( 91 cm) 3 Cut the two steel bands that secure the library and packing material to the pallet (see figure 6). Caution: The steel bands are under tension and will snap away when cut. Unpacking the Library 9 Quantum ATL 4000 Library Unpacking Instructions Document 6434005-02, Ver. 0 August 2002 Figure 6 Removing the Steel Bands 4 Lift the cardboard box top cover straight up and off of the pallet (see figure 7). Figure 7 Removing the Box Top Cover 10 Unpacking the Library Quantum ATL 4000 Library Unpacking Instructions Document 6434005-02, Ver. 0 August 2002 5 Pull the eight cardboard box retaining clips to their open position. 6 Unwrap the cardboard box from the library (see figure 8). Figure 8 Removing the Cardboard Box 7 Remove the accessory kit from the rear compartment of the crate. 8 Check the packing list and verify that all accessories have been received. Note: If any part is missing or damaged, contact your authorized reseller. 9 Lift the foam cap up and off of the library (see figure 9). Unpacking the Library 11 Quantum ATL 4000 Library Unpacking Instructions Document 6434005-02, Ver. 0 August 2002 Figure 9 Removing the Foam Cap 10 On the right side of the library, lift the wooden bar out of its brackets on the pallet (see figure 10). Figure 10 Removing the Wooden Bar 12 Unpacking the Library Quantum ATL 4000 Library Unpacking Instructions Document 6434005-02, Ver. 0 August 2002 11 On the right side of the library, unscrew the bolts that secure the hold-down brackets. figure 11), using the supplied wrench. 12 Remove each hold-down bracket from under the library (see Figure 11 Removing the Stop Blocks 13 Re-insert the left-side wooden bar in its brackets on the pallet to hold the library in place. 14 Repeat steps 10, 11, and 12 for the right side of the library. Do not replace the right-side wooden bar. 15 Slide out the two ramp extensions and the foam block, all located under the library on the right side (see figure 12). Unpacking the Library 13 Quantum ATL 4000 Library Unpacking Instructions Document 6434005-02, Ver. 0 August 2002 Figure 12 Removing the Ramp Extensions 16 Place the ramp extensions aside until the library is ready to be positioned. 17 Re-insert the right-side wooden bar into its brackets on the pallet to hold the library in place. Positioning the Library 0 To position the library: 1 Map out a route to the installation site. 2 Carefully lift the shipping bag off of the library (see figure 13). 14 Unpacking the Library Quantum ATL 4000 Library Unpacking Instructions Document 6434005-02, Ver. 0 August 2002 Figure 13 Removing the Shipping Bag 3 Inspect the library for any damage that may have occurred during shipment. Note: The ramp may be set up on either the right side or the left side of the pallet. The following illustrations show the ramp set-up procedure when the right side of the library is used. 4 Place the two ramp extensions in the slots provided at the edge of the pallet (see figure 14). Unpacking the Library 15 Quantum ATL 4000 Library Unpacking Instructions Document 6434005-02, Ver. [. . . ] 0 August 2002 Figure 24 Removing the Vertical Carriage Restraint Extension asix assembly (rotated 90 degrees) Vertical carriage assembly Vertical carriage restraint Horizontal carriage assembly Storing the Shipping Materials 0 To store the shipping and packaging materials for future use: 1 Use the screws removed in steps 6, 8, and 9 to secure the shipping restraints to the inside of the library (see figure 25). Note: The profile of each shipping restraint is clearly outlined on the storage label. Unpacking the Library 23 Quantum ATL 4000 Library Unpacking Instructions Document 6434005-02, Ver. 0 August 2002 Figure 25 Storing the Shipping Restraints Label with shipping restraints outlined 2 Slide the two ramp extensions into their shipping position on top of the pallet. 3 Secure the ramp extensions with the foam block. 6 Place the shipping bag, load port shipping plate, stop blocks, foam cap, screws, and other packaging materials on the pallet. 7 Collapse the cardboard box. 8 Place the cardboard box on top of the packaging materials on the pallet. 9 Secure the pallet, packaging materials, and cardboard box for future use. Leveling the Library 0 To level the library: 1 Rotate each foot of the library until it makes contact with the floor. [. . . ]