User manual QUANTUM 651350103A01

[. . . ] Quantum DX-Series User's Guide, 6513501-03 A01, February 2005, Made in USA. Quantum Corporation provides this publication "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation may revise this publication from time to time without notice. Making copies or adaptations without prior written authorization of Quantum Corporation is prohibited by law and constitutes a punishable violation of the law. [. . . ] The management frame displays the Security page (see figure 27). 3 46 Quantum DX-Series User's Guide Chapter 3 DX-Series Remote Management Configuration Figure 27 Security Configuration 2 Under Monitor Password, enter the desired password in the New Password field and again in the Confirm New Password field. Note: The passwords must be lowercase and limited to 15 characters. 3 Click Apply. 4 Under Administrator Password, enter the desired password in the New Password field and again in the Confirm New Password field. Note: The passwords must be lower case and limited to 15 characters. 5 Click Apply. A Results page indicates the password has been changed. Quantum DX-Series User's Guide 47 Chapter 3 DX-Series Remote Management Configuration Configuring the Fibre Channel Options 3 The DX-Series system allows you to control and configure each of the Fibre Channel input ports that connect to the customer SAN. The Fibre Channel input ports are numbered 5 through 12 on the DX100 and 5 through 6 on the DX30 (see figure 28). Figure 28 Fibre Channel Input Port Locations 11 9 75 DX100 back view (physical configurable ports) 12 10 8 6 DX30 back view (physical configurable ports) 5 6 To access the Fibre Channel page (see figure 29): 1 In the Configuration page, click Fibre Channel. The management frame displays the Fibre Channel Port Settings page (see figure 29). 48 Quantum DX-Series User's Guide Chapter 3 DX-Series Remote Management Configuration Figure 29 Fibre Channel Configuration Note: The DX-Series system must be off-line to configure the Fibre Channel options. 2 While the Port WWNs are always unique, the Node WWNs can be set according to the Make the Node WWN section as follows: a b Selecting Globally Unique but same for all ports makes the Node WWNs the same for all Fibre Channel ports. Selecting Equal to the Port WWNs for each port makes the Node WWNs equal to the Port WWNs. 3 Selecting The Port Settings page (see table 5 for field descriptions) allows you to set the AL_PA, Loop ID and link speed for each Fibre Channel port connecting the DX-Series system to the customer SAN (DX30 has two ports and DX100 has eight ports). Quantum DX-Series User's Guide 49 Chapter 3 DX-Series Remote Management Configuration Table 5 Port Settings Field Node World Wide Name (WWN) Description The node WWN is the overall system identification on the customer SAN. This field allows you to set the WWN in case a controller is replaced so the customer SAN will not require remapping. Soft allows the customer SAN to automatically assign a loop ID to the DX-Series System. This field allows you to select the maximum link speed of the Fibre Channel port (1GB/sec, 2GB/sec, or Automatic). The default setting is Automatic. AL_PA and Loop ID Speed 4 To map specific devices to Fibre Channel ports, click Device Mapping. The Device Mapping page displays (see figure 30). 50 Quantum DX-Series User's Guide Chapter 3 DX-Series Remote Management Configuration Figure 30 Device Mapping Configuration The Device Mapping page allows you to map or assign DX-Series virtual devices (robot and tape drives) to specific Fibre Channel ports. The default setting for both the DX30 and DX100: · · Port 5 is assigned the robot and tape drives 0 through 2. Port 6 is assigned tape drives 3 through 5. 5 There are two ways to assign virtual devices to a specific Fibre Channel port: a Click Auto Populate to allow the DX-Series controller to automatically assign virtual devices to a Fibre Channel port. Example: A system with 1 partition would have a robot assigned to LUN 0 and all other devices within that partition assigned to additional LUNs on that port. b Use the drop down boxes located under the port number to select the devices mapped to that port. Do NOT assign the same device to more than one port unless your backup application can support multiple mappings of the same device to more than one port. Quantum DX-Series User's Guide 51 Chapter 3 DX-Series Remote Management System Status Example: Assign the robot and tape drives 0 and 1 to port 5. From the host, only the robot and tape drive 0 and 1 are visible from port 5. 6 When all of the virtual devices have been assigned to the appropriate port, click Apply to accept the port settings. Note: Microsoft Windows has a known issue recognizing more than eight LUNs on a single Fibre Channel port. See Microsoft Knowledge Base Article 310072: http://support. microsoft. com/default. aspx?scid=kb;en-us;310072 for information on reconfiguring Windows to overcome this limitation. [. . . ] Lo smaltimento delle batterie usate deve essere disposto secondo quanto previsto dalla legge. Lo smaltimento della batteria deve essere eseguito in conformità con le leggi locali, statali e federali. Quantum DX-Series User's Guide 123 Appendix C Regulatory Statements PRECAUCIÓN Este producto contiene una batería de litio. Existe riesgo de explosión si se sustituye la batería por otra del tipo incorrecto. Deseche las baterías usadas según se indica en las instrucciones. [. . . ]