User manual QUANTUM 6473010V1R0

[. . . ] If you need help with any part of these instructions, please contact Quantum|ATL Customer Support 24 hours a day, 7 days a week, at the number for your area listed in the M1500 Library User's Guide. You can also receive help in the form of a complete set of M1500 user documents in Portable Document File (PDF) format by going to www. QuantumATL. com. Once the FC310 is installed, it must be configured using instructions found in the Quantum|ATL FC310 Bridge User's Guide (PN 6421018). [. . . ] CAUTION: Failure to take adequate antistatic precautions may result in damage to the FC310 card or other library components. STEP 2: INSTALL THE FC310 a. (If this is a standalone library, remove the two screws holding the library cover in place and slide the cover off. ) b. Loosen the two captive screws that secure the card cage to the back of the library. Locate the expansion slot closest to the SCSI adapter. SCSI controller Captive screws Slot for FC310 Handle M-Series Library Back Panel If this is a first-time installation, remove the slot cover plate and hold-down clamp. To do this, remove the screws securing the cover plate to the card cage and then lift the plate out. Remove the screws that secure the hold-down clamp to the side of the card cage. If you are replacing an FC310, remove the existing FC310 by detaching all cables, removing the hold-down clamp screws from the side of the card cage, removing the screws that secure the FC310 to the card cage, and then lifting the FC310 out of the expansion slot. NOTE: Refer to the Return Material Authorization (RMA) documents shipped with the replacement FC310 Bridge kit for the appropriate return procedure. Hold the FC310 by the edges; avoid contact with FC310 components and connectors. Press down gently on the card edge until the card is securely seated. FC310 g. Secure the FC310 to the card cage frame using the two screws provided. Slide the card cage back into the library and secure the cage by tightening the two captive screws. If this is a standalone library, slide the cover back on the library and secure it in place. M-Series Library Back Panel with FC310 Installed Fibre Channel port SCSI ports Serial port (RJ45) j. STEP 3: CONNECT SCSI CABLES a. Attach a SCSI cable from the upper SCSI port on the library SCSI controller to the first SCSI connector on drive 0. Attach a SCSI cable from SCSI port 0 on the FC310 (the left VHDCI connector) to the lower SCSI port on the library SCSI controller. If the library has two drives, attach a SCSI cable from SCSI port 1 on the FC310 (the right VHDCI connector) to the first SCSI connector on drive 1. Terminate the second SCSI connector on drive 1. Drive 0 SCSI cable (controller to drive 0) SCSI cable (FC310 to controller) STEP 4: CONNECT THE FIBRE CHANNEL CABLE a. Connect one end of the Fibre Channel cable to the Fibre Channel port on the FC310. [. . . ] Then repeat the startup procedure. STEP 6: CONFIGURE THE FC310 A command-line interface (CLI) is available to assist with FC310 configuration and maintenance as well as system diagnostics. Specifically, the CLI can be used to configure the serial, Fibre Channel, and SCSI ports; to create device maps; to obtain FC310 status information; to log FC310 events; and to report SCSI and Fibre Channel device information. For more information, refer to the Quantum|ATL FC310 Bridge User's Manual (PN 6421018). CORPORATE HEADQUARTERS 141 Innovation Drive Irvine, CA 92612-3040 USA Telephone: (949) 856-7800 Fax: (949) 856-7799 www. QuantumATL. com EUROPEAN HEADQUARTERS 7 Lindenwood Chineham Business Park Basingstoke, RG24 BWD United Kingdom Telephone: +44 1256 818300 Fax: +44 1256 848700 ASIA PACIFIC HEADQUARTERS 1st Floor Honda House I80 Kingsford Smith Drive Albion, Old 4010 Brisbane, Australia Telephone: +61 7 3862 4655 Fax: +61 7 3862 4677 Quantum|ATL maintains offices throughout the USA, Europe, and Asia Copyright 2001 ATL Products, Inc. [. . . ]