User manual QUANTUM 642300204A01

[. . . ] ATL M-Series User's Guide 6423002-04 A01 ATL M-Series User's Guide, 6423002-04 A01, September 2003, Made in USA. Quantum Corporation provides this publication "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation may revise this publication from time to time without notice. Making copies or adaptations without prior written authorization of Quantum Corporation is prohibited by law and constitutes a punishable violation of the law. [. . . ] To enable or disable drive serialization: 1 Access the Configuration screen (see Accessing the Configuration Screen on page 49). 4 Use the Up or Down buttons to select the desired Serialization setting. To return to the Configuration screen without changing the option setting, press Cancel. 6 Press Main to return to the main screen. Changing the Short Labels Setting 3 The Short Labels option controls how many bar code label characters are returned when the host issues a Read Element Status command. When Short Labels is set to: · · Off, all of the bar code label characters are returned On, only the first six characters of the bar code label are returned 58 ATL M-Series User's Guide Chapter 3 Changing the Library Configuration Changing the Illumination Setting To enable or disable Short Labels: 1 Access the Configuration screen (see Accessing the Configuration Screen on page 49). 4 Use the Up or Down buttons to select the desired Short Labels setting. 6 To return to the Configuration screen without changing the option setting, press Cancel. 7 Press Main to return to the main screen. Changing the Illumination Setting 3 The Illumination option allows you to turn the interior illumination of the library on or off. This illumination allows you to view the robotics easily through the viewing window. To enable or disable Illumination: 1 Access the Configuration screen (see Accessing the Configuration Screen on page 49). 4 Use the Up or Down buttons to select the desired Illumination setting. Note: The default setting is Enabled. ATL M-Series User's Guide 59 Chapter 3 Changing the Library Configuration Changing the Off-Line Time Setting 5 Press Select. To return to the Configuration screen without changing the option setting, press Cancel. 6 Press Main to return to the main screen. Changing the Off-Line Time Setting 3 When you access the Menu screen using the GUI, the library becomes NOT READY and will not respond to any SCSI commands issued. If you leave the library unattended in menu mode, the library goes back to a READY state after a pre-set time-out, controlled by the Off-Line Time option. You can set this time-out to any value from 1 to 99 minutes, or turn it off. To set the Off-Line Time: 1 Access the Configuration screen (see Accessing the Configuration Screen on page 49). 4 Use the Up or Down buttons to select the desired Off-Line Time setting. To return to the Configuration screen without changing the option setting, press Cancel. 6 Press Main to return to the main screen. 60 ATL M-Series User's Guide Chapter 3 Changing the Library Configuration Changing the Barcode Scanner Setting Changing the Barcode Scanner Setting 3 The Barcode Scanner option controls whether the bar code scanner is enabled or disabled. When the scanner is enabled, the library attempts to detect a bar code on all tape cartridge labels. If the correct bar code labels are not used, or if some cartridges are not labeled, scanning time may be greatly increased. [. . . ] Non guardare fisso nel fascio di luce. 4 180 ATL M-Series User's Guide Appendix D Regulatory Statements ATTENZIONE: L'utilizzo di comandi, regolazioni o procedure diversi da quelli specificati in questa sede potrebbe causare livelli di esposizione pericolosi. Dichiarazione sulla batteria della libreria 4 ATTENZIONE: Questo prodotto contiene una batteria al litio. La RAM non volatile, di tipo Dallas Semiconductor DS1743-100, contiene una batteria al litio. Smaltire la batteria secondo quanto previsto dalle leggi locali, regionali e nazionali. Dichiarazione sulla batteria MC300 4 ATTENZIONE: Qualora la batteria venga sostituita in modo non corretto, esiste il pericolo di esplosione. Sostituire solo con lo stesso tipo di batteria o con un tipo equivalente consigliato dal produttore. [. . . ]