User manual QUADRA FIRE 839-1290

[. . . ] R Tested and Listed by O-T L C US Portland Oregon USA TOPAZ DIRECT VENT ROOM HEATER OMNI-Test Laboratories, Inc. Owner's Manual Installation and Operation Model: 839-1290 839-1320 839-1340 844-4120 TOPAZ-D-CSB TOPAZ-D-CWL Quartet Front Solitaire Front CAUTION DO NOT DISCARD THIS MANUAL · Important operating and · Read, understand and · Leave this manual with follow these instructions maintenance instructions party responsible for use for safe installation and included. operation. D DI O N SC O AR T D WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death. · Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. · What to do if you smell gas - Do not try to light any appliance. · Installation and service must be performed by a qualified installer, service agency, or the gas supplier. This appliance may be installed as an OEM installation in manufactured home (USA only) or mobile home and must be installed in accordance with the manufacturer's instructions and the manufactured home construction and safety standard, Title 24 CFR, Part 3280 or Standard for Installation in Mobile Homes, CAN/CSA Z240MH. [. . . ] If there is sheet rock only (no studs) in front of the masonry the 10 in. This allows the retro connector to mount directly on the masonry and provide the correct clearances to combustibles (Figure 5. 25). Figure 5. 26 Step 4. (76mm) above the top of the flashing down to the level of the opening. (51-76mm) of flex above the existing chimney to allow for connection to the termination kit. Connect the flex liner to the top adapter using three sheet metal screws (Figure 5. 21 page 19). Carefully feed the flex liner down the chimney to the bottom and out the opening in the masonry wall, forming an angle to line up the flex liner with the vent opening on the appliance. Studwall 10 in. (254mm x 254mm) framed opening in wall Retro Connector Masonry Chimney WARNING Wall Thimble Cover (4) Masonry Bolts (Not Included) NOTE: For hearth applications refer to page 20, Figure 5. 24 for the use of a co-axial to co-linear appliance connector. · Do not let the flex liner sag below the level at which it will connect to the appliance or connector. This could allow hot gas to become trapped and potentially become a fire hazard. The flex liner path should always be sloped up toward the termination cap. Step 3. Secure the flashing to the top of the masonry chimney using a bead of non-hardening sealant-adhesive. If the flashing is larger than the top of the chimney, cut and fold flashing as needed to fit chimney (Figure 5. 26). Step 7. If additional lengths of flex liner are needed to span the chimney height, use a flex coupler to connect the pieces of flex liner together. Connect the flex to the coupler by using four sheet metal screws for each side (Figure 5. 27, on the next page). September 1, 2008 Quadra-Fire · Topaz · 7009-113G Page 21 Flex Liner 6 in. (152mm) diameter opening in masonry wall Flex Coupler Sheet Metal Screws Retro Connector Figure 5. 27 Figure 5. 29 (3) Masonry Bolts (Not included) Step 8. Use three sheet metal screws through the side of the top adapter into the flange on the flashing (Figure 5. 28). Twist lock the high wind termination cap on to the top adapter. High Wind Termination Cap Step 10. Slide wall thimble cover over retro connector and secure with masonry bolts (Figure 5. 30). If you have a framed wall in front of the masonry, use wood screws to mount wall thimble cover to framed wall, over retro connector and 10 in. If needed, add a section of direct vent pipe to the retro connector in order to extend through the opening in the wall thimble cover. Top Adaptor (3) Sheet Metal Screws Retro Connector Wall Thimble Cover (4) Masonry Bolts (Not included) Flashing Figure 5. 28 Figure 5. 30 Step 9. Use three sheet metal screws to attach the flex liner to the connector (Figure 5. 29). Be careful to ensure that the connector is centered in the opening and the mounting holes line up with the masonry wall. Step 11. [. . . ] Warranty Period Parts Labor HHT Manufactured Appliances and Venting EPA Wood Pellet Electric Wood X X X X Gas Venting Components Covered All Parts and Material Except as covered by Conditions, Exclusion, and Limitations listed Igniters, Electronic Components, and Glass Blowers Molded Refractory Panels 1 Year X X X 2 years X X X 3 years 5 years 7 years 10 years Limited Lifetime 3 years 3 years 1 year 1 year X X X X X X X X X Firepots X X Castings & Baffles Firebox, HHT Chimney, Termination & Heat Exchanger Burners, Logs & Refractory Firebox & Heat Exchanger X X X X X X 9-01-08 All Replacement Parts 90 Days See Conditions, Exclusions, and limitations. CONDITIONS, EXCLUSIONS & LIMITATION OF LIABILITY This warranty applies to the original owner and is transferable up to two years from date of purchase to the new homeowner, provided the purchase was made through an authorized dealer or distributor of HHT, and the appliance remains in its original place of installation. The maximum amount recoverable under this warranty is limited to the purchase price of the product. In no event shall HHT be liable for any incidental or consequential damages caused by defects in the product. [. . . ]