User manual QUADRA FIRE 31ST-ACC

[. . . ] R 3100 WOOD STOVE SERIES Advanced Combustion Control (ACC) Owner's Manual Installation and Operation Tested and Listed by O-T L C US Portland Oregon USA OMNI-Test Laboratories, Inc. Models: 31M-ACC-MBK 31ST-ACC Step Top Uni-Body Model (Pedestal Model Shown) Millennium Model CAUTION DO NOT DISCARD THIS MANUAL · Important operating and maintenance instructions included. · Read, understand and follow these instructions for safe installation and operation. · Leave this manual with party responsible for use and operation. T O N RD OA D SC I D WARNING If the information in these instructions is not followed exactly, a fire may result causing property damage, personal injury, or death. · Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. [. . . ] Tools Required: Phillips head screwdriver, 7/16 socket wrench, /2 and 5/6 Allen wrench. Remove the 2 nuts and 2 bolts holding the channel in place and set the channel aside. The glossy side of the gasket needs to go against the firebox bottom. Door Handle Gasket 2 7 3100 Wood Stove Series (ACC) Appliance Set Up 2 Remove for installation and then re-install Figure 21. 1 It is important the gasket is not put on upside down as it could compromise its sealing capabilities. Install ash door assembly by sliding the rod at an angle into the slot on the left side. As the rod starts passing through the slot, slide the handle over the rod and then finish pushing the rod through the slot. Slide the ash door over the 4 screws protruding from the bottom of the stove. This magnet will hold the door handle in an open position which in turn holds the ash door open so ashes can be brushed into the ash drawer. Figure 21. 2. Lay stove flat on protective padding or pallet Magnet Slide rod at an angle into slot Ash Door Assembly Figure 21. 2 Set Screw (align with flat side of rod) WARNING Do NOT operate before fully assembling components. Burning your stove without a pedestal or leg kit attached: · · Will void your warranty. May result in property damage or personal injury. Door handle must be in open position to tighten set screw Ash Door Rod shown in installed position Figure 21. 3 September 1, 2008 7033-277F Page 21 3100 Wood Stove Series (ACC) Pedestal and Ash Removal System (Cont'd) Installing Pedestal Assembly 1. Remove screws on adapter and slide pedestal over adapter on bottom of stove. Re-install the ARS channel that was removed in Step on page one and secure with 2 bolts previously removed. Check to make sure baffle boards and ceramic blanket are in their proper locations. NOTE: If installing a floor installation of an outside air kit on a Step Top model with a pedestal assembly you must attach the enclosed cover plate to the back of the stove. Figure 22. 3. Figure 22. 2 Grate ARS Channel R Replace both bricks back into firebox Adapters Ash Removel Drawer Figure 22. 3 Cover Plate Oak Pedestal Trim Figure 22. 1 Page 22 7033-277F September 1, 2008 R 3100 Wood Stove Series (ACC) B. Leg Kit and Ash Removal Installation (ARS) for Step Top Uni-Body NOTE: The Ash Removal System, must be installed first before installing the legs. Installing Leg Kit 1. Attach the 2 bottom screws of the mounting brackets to the bottom of the stove with 1/4"-20 Phillips head screws. Leave the bottom 2 screws loose so you can slide the ash pan assembly bottom slots over the screw heads. This allows the weight of the ash pan to rest on the screws while you are attaching the top 2 screws. Loosely assemble bolts into the corner of the mounting brackets for leg attachment. See also Figure 22. 2. Figure 23. 2 Lay stove flat on its back on protective padding or pallet Ash Drawer Leg Brackets Insert 2 bottom screws loosely Do NOT tilt the unit on the cast iron legs. Lift the unit upright and place it into position on the floor protector. CAUTION Leg Mounting Brackets are packaged inside firebox. Leveling Legs at opposite corners Figure 23. 1 September 1, 2008 7033-277F Page 2 3100 Wood Stove Series (ACC) C. [. . . ] Warranty starts with date of purchase by the original owner (End User) except as noted for replacement parts. Warranty Period Parts Labor HHT Manufactured Appliances and Venting EPA Wood Pellet Electric Venting Wood X X X X X Components Covered All Parts and Material Except as covered by Conditions, Exclusion, and Limitations listed Igniters, Electronic Components, and Glass Blowers Molded Refractory Panels X X X X X X X X X X X 9-01-08 X X X Firepots Castings & Baffles Firebox, HHT Chimney, Termination & Heat Exchanger Burners, Logs & Refractory R Gas 1 Year X X 2 years X X X years 5 years 7 years 10 years Limited Lifetime years years 1 year 1 year X X X Firebox & Heat Exchanger All Replacement Parts 90 Days See Conditions, Exclusions, and limitations. CONDITIONS, ExCLUSIONS & LIMITATION OF LIABILITY This warranty applies to the original owner and is transferable up to two years from date of purchase to the new homeowner, provided the purchase was made through an authorized dealer or distributor of HHT, and the appliance remains in its original place of installation. The maximum amount recoverable under this warranty is limited to the purchase price of the product. [. . . ]