User manual PYLE PWMA3600

[. . . ] Pulling the levers upward and out to makes it possible to remove the unit. DIN REAR-MOUNT Installation using the screw holes on the both sides of the unit. 1 Fastening the unit to the factory radio mounting bracket. Select a position where the screw holes of the bracket and the screw holes of the main unit become aligned (are fitted), and tighten the screws at 2 places on each side. Use either truss screws (5 x 6mm) or screws (4 x 6mm), depending on the shape of the screw holes in the bracket. Hook and Screw (Remove this part) Note: The frame, strap, and half-sleeve are not used for REAR-MOUNT. 2 5 4 2 3 5 4 HOW TO OPEN AND CLOSE THE SCREEN DISPLAY 1. [. . . ] Push the panel, the display will be drawn in. 6 BLUE/WHITE POWANT RED ACC YELLOW MEMORY BLACK GROUND CHOKE BOX TO POWER SUPPLY REAR Rch SPK VIOLET/BLACK TV CONTROL GREY/BLACK GREEN GREEN/BLACK GREY VIOLET REAR Lch SPK GREY GREY/BLACK TV DIVERSITY ANTENNA INPUT FRONT Rch SPK TV DIVERSITY ANTENNA INPUT ELECTRICAL CONNECTION RADIO/TV MAIN UNIT (VIEW FROM REAR) FRONT Lch SPK WHITE/BLACK WHITE RADIO ANTENNA INPUT 7 (BROWN) Rch RED Lch WHITE (GREY) Rch RED Lch WHITE FRONT RCA CABLE REAR RCA CABLE (FOR RCA LINE VERSION ONLY) 75ohm RF WIRE (BLACK) VIDEO OUTPUT AV1 AV2 AV INPUT VIDEO AUDIO­R AUDIO­L FROM VIDEO/AUDIO SOURCE DISPLAY UNIT TV MONITOR BLACK CABLE BLACK PLUG BLACK/GREY CABLE GREY PLUG RADIO CONTROL RADIO/TV MAIN UNIT (VIEW FROM FRONT) RADIO CONTROL TV MONITOR OPERATION 16 11 7 24 4 2 13 1 5 6 8 12 15 3 14 19 10 20 9 18 21 8 22 17 1 23 4 GENERAL OPERATION · ON/OFF Switch on the unit by pressing PWR button (1). · FACEPLATE RELEASE Press REL button (2) to draw out the faceplate, push the panel to draw in. When the faceplate is drawn out, turn the faceplate upward and adjust TV display. · SELECTING SOUND MODE Press SEL button (6) to move display through volume, bass, treble, balance and fader functions. When mode has not been adjusted for several seconds, display returns to previous display status. VOL (Volume) BAS (Bass) TRE (Treble) BAL (Balance) FAD (Fader) Volume Adjust volume level using (7) and (8) buttons. Adjust treble level using Balance Press SEL button (6) for three times. Adjust sound balance between left and right speakers using (7) and (8) buttons. Adjust sound balance between front and rear speakers using (7) and (8) buttons. · SELECTING PLAYING MODE When the screen display is drawn out, the unit would automatically switch into TV mode. By pressing MOD button (12), you can select desired playing mode among TV and radio. CAUTION: The unit cannot be switched into TV mode, when the car is running. Press MENU button (18) for the first time: PICTURE TUNE SYSTEM MENU PIC ADJUST Press the MENU button repeatedly or press CH+ button (9) or CH­ button (10) to select the desired sub-menu then press CONTROL+ button (19) or CONTROL­ button (20) to enter the corresponding sub-menu to set. The menu allows picture adjustment such as bright, contrast, color, and etc. SYSTEM MENU This menu includes the items for system control, such as color, sound, language, and etc. The details please refer to SYSTEM MENU. PICTURE MENU PICTURE MENU BRIGHT CONTRAST COLOR SHARP TINT 20 25 45 63 10 Use CH+ button (9) or CH­ button (10) to select picture mode upward or downward. Then use CONTROL+ button (19) or CONTROL­button (20) to adjust the selected item. 12 Note: When you set the color mode to "PAL" in SYSTEM MENU, there is no "TINT" item to display. In this menu, the range of setting value is 00~63, and the recommended range of these values are listed below: BRIGHT: 10~32 CONTRAST: 20~40 COLOR: 40~50 SHARP: 63 TINT: 10 TUNER MENU --POSITION -TUNER MENU POS SKIP BAND FINE AFT SEARCH ASM 1 ON UHF OFF POSITION setup You can use numeric buttons to input the TV channel number. For example, you input 8, when you turn off the unit and then turn it on again, the program of channel 8 will be displayed. --SKIP-TUNER MENU POS SKIP BAND FINE AFT SEARCH ASM 1 ON UHF OFF SKIP setup You can use CONTROL+ button (19) or CONTROL­ button (20) to switch between ON and OFF. If you set the position to 8 and select SKIP to ON, when you press CH+ button (9) or CH­ button (10) to choose channel, the channel 8 will be skipped. 13 --BAND-TUNER MENU POS SKIP BAND FINE AFT SEARCH ASM 1 ON UHF OFF BAND setup You can use CONTROL+ button (19) or CONTROL­ button (20) to switch between UHF, VHFL and VHFH band. --FINE-TUNER MENU POS SKIP BAND FINE AFT SEARCH ASM 1 ON UHF OFF FINE setup When the frequency has warp, and the picture displayed unstable, you can use CONTROL+ button (19) or CONTROL­ button (20) to start FINE function to adjust it. --AFT-TUNER MENU POS SKIP BAND FINE AFT SEARCH ASM 1 ON UHF OFF AFT (Auto Frequency Trace) setup Use CONTROL+ button (19) or CONTROL­ button (20) to switch between ON and OFF. 14 --SEARCH-TUNER MENU POS SKIP BAND FINE AFT SEARCH ASM 1 ON UHF OFF SEARCH setup Use CONTROL+ button (19) or CONTROL­ button (20) to start manual station search. --ASM-TUNER MENU POS SKIP BAND FINE AFT SEARCH ASM 1 ON UHF OFF ASM (Auto Search Memory) setup Use CONTROL+ button (19) or CONTROL­ button (20) to start auto station search. When the search completed and all stations that searched have been stored in the unit, it will exit search mode. Note: - Before auto search memory, you must enter into SYSTEM MENU to set COLOR mode to "AUTO" and the SOUND mode according to the local region first. [. . . ] - The number of the program that searched is just the channel-stored number and it does not match the real channel number. If you want get the real channel number, you can press SORT button to arrange these channels. SYSTEM MENU --COLOR-SYSTEM MENU COLOR SOUND LANG. B/B CORING HALFTONE AUTO M ENGLISH ON ON ON 15 COLOR setup Use CONTROL+ button (19) or CONTROL­ button (20) to switch color mode among AUTO, PAL, N3. 58 and N4. 43. B/B CORING HALFTONE AUTO M ENGLISH ON ON ON SOUND setup Use CONTROL+ button (19) or CONTROL­ button (20) to switch sound mode among M, B/G, I and D/K. [. . . ]