User manual PYLE PT649D

[. . . ] PANEL INFORMATION 1 2 3 4 5 6 2 DECK B COUNTER LEVEL METER INDICATION FWD NOISE REDUCTION REC LEVEL FWD A PLAY DYNAMIC NOISE REDUCTION FULL AUTO STOP SYSTEM OFF ON MIN MAX B REC/PLAY HIGH SPEED DUBBING FULL AUTO STOP SYSTEM PLAY CrO2 DUBBING HI. SP. DUB. REC CrO2 POWER ON OFF PLAY REW FF STOP/EJ. PAUSE REC PLAY REW FF STOP/EJ. PAUSE 7 11 10 9 8 7 1. Press release to switch "OFF" unit into "STANDBY MODE". If the unit is left unattended for long periods, remove the 13 AMP plug from the power socket. [. . . ] DUBBING SWITCH Press the DUBBING button when you need Dubbing at normal speed. PLAY Cr02 SWITCH When play Cro2 tape, press this button. -1- OPERATING PROCEDURES VOLTAGE SELECTOR Use this switch to se lect the pr op er Volt age fo r yo ur reg ion VOLTAGE SELECTOR DC LIN E (IN)REC PLAY(O UT) 110~120V 60Hz 220~230V 50Hz RISK OF ELECTRIC SHOCK DO NOT OPEN CASSETTE DECK INTEGRATED CIRCUIT REMOTE SY STEM TO AMP PA T UNER R EM O T E S YS TE M EQ TA PE T UNER CD V O LTAG E S EL EC T O R 1 10 ~ 1 20 V 2 20 ~ 2 30 V 6 0H z 5 0H z R IG HT L E FT TA PE CD AV1 AV2 A UX PLAY REC PLAY EQ REC L IN TE G R ATE D C IR C U IT A C 22 0 V - 23 0 V ~ 50 H z L _ R _ AU DIO Playback a recorded tape ( DECK A or DECK B) 1. For Cr02/metal tape, further press the Cr02/metal switch and the light at the indicator will be lit up. Adjust the AMPLIFIER VOLUME and GRAPHIC EQUALIZER controls for your desired sound level and taste. Fast forward and rewind (DECK A or DECK B) For fast winding or rewinding the tape, press the FFWD or REW button. Press the STOP/EJECT button when the desired location has been reached. When the end of the tape has been reached, the FFWD or REW button will be released automatically. Pause (DECK A or DECK B) Press the PAUSE button to momentarily stop tape travel during playback or recording. Re-press the button for pause release and playback or recording to re-start. Full automatic stop (DECK A or DECK B) Press the STOP/EJECT button to stop playback or recording at any time. When the end of the tape has been reached, any of the PLAY, REC, REW or FFWD buttons, if pressed, will be automatically released and the head block completely separates from the tape and capstan. Manually level control recording (for external source) This unit has record level volume to adjust the record level. When it reached the center click position, the tapes can be recorded normally. If the sound source signal is too strong, a red spot will be appeared in the record level indicator. You can adjust the record level volume to the left position and vice versa. In normal state, the sound source level is between the red and green spots ( that's 0dB). [. . . ] . 40dB (1 khz) Head. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Deck A For Playback Deck B For recording/playback, 2-gap ferrite head for erasure Design and specifications are subject to change without notice. rd Motor. . . . . . . . . . . . . . . . . . . . . . . . . . . DC servo motor x 2 Fast Forward/Rewind time. . Approx. 100 sec with C-60 cassette Input terminals LINE IN X 2. . . . . . . . . . . . . . . . . . Min. input level:600mV(0dB) Input impedance: 50 k Output terminals LINE OUT X 2. . . . . . . . . . . . . . . . output level: 600mV (0dB) output impedance: 5 k Power requirement. . . . . . . . . . . . AC220V, 50Hz power voltage. . . . . . . . . . . 230V, 50Hz For U. K. . . . . . . . . . . . . . . . . . 240V, 50Hz For U. S. A. & Canada. . . 110V, 60Hz Power consumption. . . . . . watts VA Rated watts Maximum Dimensions. . . . . . . . . . . . . . . . . . . . . 360mm x 128m x246mm (W x H x D) Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . 4Kg (8. 5 Ibs) ACCESSORIES. . . . . . . . Pin plug cord. . . 2 H. D. [. . . ]